evertz 3080UEP Series User Manual Download | Manualshive

Page: 19 / 62

background image

3080UEP Series

Professional 3G/HD/SD Universal Contribution Encoding Platform

Revision 0.2

Page - 11

4.

VISTALINK

®

PRO INTERFACE

4.1.

SYSTEM

The system tab has IP port addresses, system information and common controls which are applicable
to all UEP onboard encoders.

Figure 4-1: VistaLINK

®

PRO – System

Firmware Version:

This parameter returns the firmware version on the card.



Note: For IP address settings on Control and Data ports. After applying any
changes, the UEP must be rebooted for the changes to take. Reboot can be pressed
at the bottom of this System tab after all changes are made.

Control Port

IP Address:

Allows user to set the IP Address for the Control Port.

NetMask:

Allows user to set the Subnet NetMask for the Control Port.

Gateway:

Allows user to set the Gateway for the Control Port.

«
...
17
18
19
20
21
...
»

Summary of Contents for 3080UEP Series































































Reviews:

No comments

Related manuals for 3080UEP Series

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 174

Brand: Danfoss Pages: 7

Brand: Danfoss Pages: 16

VLT 2800 Series

Brand: Danfoss Pages: 34

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 60

VLT 5000 Series

Brand: Danfoss Pages: 63

Brand: M-system Pages: 5

Brand: NAIM Pages: 22

Brand: CEL-MAR Pages: 12

Brand: B&B Electronics Pages: 5

CSI 23KTL-CT/US-480

Brand: CanadianSolar Pages: 88

Brand: MAGIRA Pages: 58

Brand: Kostal Pages: 12

Brand: Parasound Pages: 7

Brand: Elenco Electronics Pages: 12

Brand: EZIHEAT Pages: 34

Brand: Transition Networks Pages: 7

-NAFR-F720-00167-NA

Brand: Mitsubishi Pages: 413

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands