manualshive.com logo in svg

ETC SMARTRACK, User Manual, Page: 4 / 61

Share
Download
ETC SMARTRACK User Manual Download Page 4

4.5.4 Cascading a stack of Smartracks  ...........................................17

4.6.

Load wiring..........................................................................19

4.6.1 Installing load wires ..............................................................19

4.7.

Identifying and testing power and load wiring..........................19

4.8.

Signal wiring .......................................................................20

4.9.

Power assemblies .................................................................21

4.9.1 Installation ...........................................................................21
4.9.2 Connecting load wiring .........................................................21
4.9.3 Connecting power wiring – RCD option fitted...........................23
4.9.4 Connecting power wiring – without RCD option .......................25
4.9.5 The power assembly signal looms ...........................................25

4.10

Smartrack door ....................................................................27

4.10.1 Mounting the door ................................................................27
4.10.2 Connecting earth and power wiring........................................27
4.10.3 Smartrack CPU jumper settings ...............................................27
4.10.4 Connecting power assembly signal looms................................28
4.10.5 Connecting DMX input/output wiring ......................................29
4.10.6 Fitting blanking plates ...........................................................29
4.10.7 Closing the door...................................................................29
4.10.8 Fitting dimmer number strips ..................................................30

5. Commissioning and configuration.......................................31

5.1.

Switching on ........................................................................31

5.2.

Power and signal indicators ...................................................31

5.3.

Modular Smartrack dimmer level indicators..............................32

5.4.

Battery supported memory .....................................................33

5.5.

Using offline mode................................................................33

5.5.1 Verifying rms line voltage in offline mode ................................34
5.5.2 Setting the output voltage range in offline mode .......................34

5.6.

Testing dimmer circuits with the rotary potentiometer .................35

5.7.

DMX control.........................................................................35

5.7.1 Terminating the DMX line.......................................................36

page iii

Smartrack User Manual

Version 1.2

Summary of Contents for SMARTRACK






























































Reviews:

No comments