ETC SMARTRACK User Manual Download Page 15 | Manualshive

Page: 15 / 61

ETC SMARTRACK User Manual Download Page 15

3. Getting started – what’s in the box

3.1. Smartrack

Smartrack systems are shipped broken down into racks and power assemblies
(up to three per rack). Please check carefully to verify that you have everything
you need before starting the installation.

3.1.1 Rack

Each rack is shipped separately as an empty enclosure, with separately
wrapped door assembly and a number of internal fittings kits, namely:

Metalwork Kit

2 x power cable entry cover
2 x load cable entry cover

Hardware Kit
Door Kit

2 x M4 black washer
1 x M4 shakeproof washer
1 x M4/10 Pan Posi Screw
1 x graphics layer number sheet

Entry Cover Kit

32 x M4/6 taptite screw
32 x M4 spring washer

Fan Kit

3 x M5/10 Pan Posi screw
3 x M5 nylon washer

Foot Kit

4 x plastic feet
4 x M5/16 csk screws
4 x plastic plugs

Power Terminal Safety Cover Kit

1 x Plastic Safety Cover
3 x M5/12 taptite screw

Remove the door assembly from the carton and store it separately while
the racks are installed and wired. It’s not needed until the installation of
the wiring and power assemblies is complete.

page 8

Smartrack User Manual

ETC Ltd

«
...
13
14
15
16
17
...
»

Summary of Contents for SMARTRACK






























































Reviews:

No comments