manualshive.com logo in svg

ETC SMARTRACK, User Manual, Page: 35 / 61

Share
Download
ETC SMARTRACK User Manual Download Page 35

Jumper Settings

J1

Top Power Assembly

12 12x2.5kW
6

6x5kW

3

3x10kW

J2

Middle Power Assembly

12 12x2.5kW
6

6x5kW

3

3x10kW

J3

Bottom Power Assembly

12 12x2.5kW
6

6x5kW

3

3x10kW

J4

CPU Configuration

R Smartrack
P

Smartpack

O

Spare

J6

DMX Termination

U Unterminated
T

Terminated

DMX Input/Output Terminal

D+

Data +

D–

Data –

SCR

Screen (ground)

4.10.4 Connecting power assembly signal looms

Using the flat ribbon cable clips mounted inside the Smartrack, run the rib-
bon cable from the top power assembly around the top of the rack, and
terminate to the top position on the Smartrack CPU. Fold any excess cable
flat inside one of the cable clips.

In the same way, run the ribbon cables from the middle and lower power
assemblies around the bottom of the rack, and terminate to the middle and
lower positions on the Smartrack CPU. Fold any excess cable flat inside
one of the cable clips.

page 28

Smartrack User Manual

ETC Ltd

J4

R P O

J1

12

6 3

CON 1

12

6 3

J2

CON 2

CON 3

12

6 3

J3

J6  U

T

CON 8

D+ D– SCR

Summary of Contents for SMARTRACK






























































Reviews:

No comments