ETC SMARTRACK User Manual Download Page 37 | Manualshive

Page: 37 / 61

ETC SMARTRACK User Manual Download Page 37

4.10.8 Fitting dimmer number strips

Self adhesive numbering strips are provided to give smart and permanent
identification of dimmer numbers on the front of the rack. Each Smartrack
is provided with one sheet containing the numbers 1–240. Spare sheets
and higher numbers are available from ETC, under the following part num-
bers:

2000A4000

1–240

2000A4001

241–480

2000A4002

481–720

2000A4003

721–960

a)

Simply peel off the numbers required and cut strips to length with a
pair of scissors as necessary.

b)

Press into place above the appropriate circuit breakers, in the detent
left by the cutout in the door’s graphic layer.

c)

Fill any gaps (to the right of the circuit breakers on 5kW and 10kW
dimmers) with the blank strips provided.

page 30

Smartrack User Manual

ETC Ltd

181 182 183 184 185 186 187 188 189 190 191 192

Peel off numbering strips

and press into place on the

front panel.

Spare sheets of numbers

may be obtained from

ETC distributors.

«
...
35
36
37
38
39
...
»

Summary of Contents for SMARTRACK






























































Reviews:

No comments