manualshive.com logo in svg

ETC SMARTRACK, User Manual, Page: 38 / 61

Share
Download
ETC SMARTRACK User Manual Download Page 38

5. Commissioning and configuration

5.1. Switching on

a) For the first switch-on only, first set all MCBs and RCDs (if fitted) to the off

(down) position.

b) Switch on power to the rack, and check that the three yellow power supply

LEDs L1, L2 and L3 are on, indicating that power from all three phases is
reaching the power supply section. If not, switch off, check wiring and
repeat.

c) If RCDs are fitted, switch them on. If any RCDs trip at this stage, there is an

earth wiring fault in the dimmer rack.

d) Switch on MCBs, one by one. If any RCDs trip at this stage, there is a power-

fault in the power assembly.

5.2. Power and signal indicators

The following status indicators are provided on the control panel. Check that
their status is correct before continuing:

page 31

Smartrack User Manual

Version 1.2

L1

DMX

✔

L2

DMX

✘

temp

L3

level

dimmer profile

speed

enter

0 0 1

Smartrack Control Panel,

showing default start

address (001)

0 0 1

Summary of Contents for SMARTRACK






























































Reviews:

No comments