background image

If 1 hour before "Normal Shower Time" set in "Time and Timer Setting" under Basic Operation , hot water temperature 
has still not reached the set value, unit will activate standard hot water operation to ensure you can enjoy enough hot 
shower water at/after this time.

These parameters are valid only for the units with heat recovery function. For the unit without this function, "Heat 
Recovery Function" should always set to 1 (invalid).

If it is set to ON, unit will try to heat up the hot water by recover the wasted heat in heating and cooling operation. 
It will turn ON heat recovery circuit if actual hot water temperature is "Hot Water Restart Based On ∆T in Heat Recovery
 Operation" lower than set hot water temperature, and stop after it heat the hot water to "Hot Water Stop Based On ∆T in 
Heat Recovery Operation" over set hot water temperature.

Working Procedure of Shifting Priority Function:

Parameter No.

Meaning

Range

Default Value

Working of Extra Heating Source for 
Hot Water in Shifting Priority
 Operation

E7

0 (no), 1(yes)

0

Parameter No.

Meaning

Range

Default Value

Hot Water Min. Working Hours in 
Shifting Priority Operation

Heating Max. Working Hours in 
Shifting Priority Operation

E5

E6

20 - 180 (in minutes)

20 - 180 (in minutes)

5

30

50

If "Shifting Priority" function is turned ON in "Temperature Parameter" setting under Basic Operation, when actual 
ambient temperature is lower than 

"

Shifting Priority" setting, Shifting Priority function will be activated.

Unit will firstly work in Hot Water Mode. If it gets the set temperature for hot water, or it has been working in Hot Water 
Mode over "Hot Water Min. Working Hours in Shifting Priority Operation", and temperature for heating has dropped 
over "Allowable Temp Drift In Heating in Shifting Priority Operation" based on set heating temperature, unit switch to 
heating. After switch to heating operation, if it gets the set temperature for hot water, or it has been working in heating 
operation for over " Heating Max

Working

 

Hours

 

in

 

Shifting

 

Priority

 

Operation

", 

unit

 

switch

 

back

 

to

 

hot

 

water

This

 

process

 

will

 

repeat

 

continously

E4

        

Allowable Temp Drift In Heating in 

                    Shifting Priority Operation

             

3 - 20 (in

)

In shifting priority operation, when the unit switches to heating , this function can be activated to turn on extra heating 
source for hot water, and help to reach the set temperature for hot water. 
If Parameter E7 is set as 1, the extra heating source for hot water will turn on when unit switches to heating in shifting 
priority operation.
If Parameter E7 is set as 0, the extra heating source for hot water will turn off when unit switches to heating in shifting 
priority operation.

Note: The extra heating source for hot water should be connected to the port HTW on the indoor PCB toactivate 
the function. For AWT model, this function is invalid, because 1.5KW electric heater inside the water tank is 
controlled bydigital thermostat directly, and there is no other heating source connected to HTW port. 

The running time for DHW 
is cleared. Unit Starts heating
 and counting the running time.

Unit keep on working in DHW
 and counting the running time. 

The ambient temp. 
Is below 

Whether the 
unit works in 
DHW

 Whether unit works 
in DHW over 

 House heating water temperature 
drops over 

Whether unit works in 
Heating over 

The running time for Heating is 
cleared. Unit starts DHW and 
counting the running time.

Unit keep on working in Heating 
and counting the running time.

 

Unit works in heating

YES

NO

YES

YES

YES

YES

NO

NO

3. Usage

58

Summary of Contents for AWH11-V5+























































































Reviews: