QuadroM 32x/8L/26x/12Li/26xi Manual II: Administrator's Guide
Administrator’s Menus
QuadroM 32x/8L/26x/12Li/26xi; (SW Version 5.2.x)
96
•
Local Dial Plan
– indicates the number and pattern of digits dialed by the user in order to reach a particular destination.
•
Send Dial Plan Terminator
– is used to switch a dial plan terminator or timeout. When the IP phone is configured to use a dial plan
terminator (such as the pound sign (#)), the phone waits for 4 or 5 seconds after the handset is picked up or a key is pressed to place a
call.
Play a Ring Splash
- is used to switch a "call waiting tone" when there is an incoming call on the BLF (Busy Lamp Field) monitored extension. If the
host tone is idle, the tone plays a "ring splash".
Snom
configuration page contains the following components:
•
Dial-Plan String
– indicates a dial plan string used to match dialed digits from the handset to the certain actions, e.g. dialing.
Dialog-Info Call Pickup
- is used to switch a subscription to the status information of SIP URLs mapped as “Destination/Extension” on the
programmable keys.
•
Transfer on Onhook
- is used to switch the call transfer when the handset is placed on hook.
•
Call join on Xfer (2 calls)
- when this option is enabled, you will connect the newly arrived incoming call to the call on hold by pressing
Xfer button. When this option is disabled and you press the Xfer button, you will have an option to choose the call on hold to transfer the
newly arrived incoming call to, or to dial a new destination manually.
•
Message LED for Dialog State/Missed Calls
– when this option is enabled, the phone will indicate missed calls and changing dialog
states using the message LED.
•
Dialtone during Hold
- when this option is enabled and the call is held the
caller gets dial tone. Otherwise there will be no dial tone after
pressing
Hold
.
•
Do not Disturb
– this selection allows you to manipulate with the IP phone DND service. When the
*72
is selected from this list, the DND
service of the IP Phone and the DND service of the Quadro for the corresponding extension will be activated when enabling the DND
service from IP Phone. This option is recommended. When
keyeventF_DND
is selected only DND service of the phone will be activated
when enabling the DND.
•
Record Missed Calls
– when this option is selected, the information about the missed calls will be displayed on the IP Phone.
Any parameters not listed above or parameters defined in this page for other IP phone models can be found in the user’s manual of the
corresponding IP phone.
Please Note:
Save changes before moving among the configuration pages.
IP Phones Logo
The
IP Phones Logo
page is used to upload a custom logo for
the IP Phones. This page contains only those IP phones for
which Quadro supports the custom logo upload. The uploaded
custom logo will be visible on the display of the IP phone.
The
Enable
checkbox is used to enable the custom logo for the
selected IP phone model(s).
The
Browse
button opens the file-chooser to select the custom
logo file.
Fig. II-172: IP Phones Logo
FXS Gateway Management
The Quadro FXS Gateway is an analogue Gateway that allows
connecting analogue phones to a VoIP network. The device can
be used with QuadroM IP PBXs to emulate additional FXS
ports. Both QuadroM IP PBX and the FXS Gateway should be
located in the same network. QuadroM IP PBX is connected to
the Quadro FXS gateway through its MAC address.
The
FXS Gateway Management
page is used to define
Quadro FXS Gateway devices in your network that can serve
as FXS expansion modules for your QuadroM IP PBX.
Additional FXS lines provided by the FXS Gateway can be
connected to the IP lines on the QuadroM IP PBX.
Fig. II-173: FXS Gateway Management page
