manualshive.com logo in svg

Epson S1C63616, Technical Manual

The Epson S1C63616 Technical Manual is a comprehensive guide for users seeking detailed information about the product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for optimal usage and troubleshooting. Get the most out of your Epson S1C63616 with this reliable manual.

Share
Download
background image

SIC63616-(Rev. 1.0) NO. P174

3240-0412

5.2  Summary of Notes by Function

Here, the cautionary notes are summed up by function category. Keep these notes well in mind when 
programming.

Memory and stack

(1)  Memory is not implemented in unused areas within the memory map. Further, some non-implemen-

tation areas and unused (access prohibition) areas exist in the peripheral I/O area. If the program that 
accesses these areas is generated, its operation cannot be guaranteed. Refer to the I/O memory maps 
shown in Table 4.1.1 for the peripheral I/O area.

(2)  Part of the RAM area is used as a stack area for subroutine call and register evacuation, so pay attention 

not to overlap the data area and stack area.

(3)  The S1C63000 core CPU handles the stack using the stack pointer for 4-bit data (SP2) and the stack 

pointer for 16-bit data (SP1).
16-bit data are accessed in stack handling by SP1, therefore, this stack area should be allocated to the 
area where 4-bit/16-bit access is possible (0100H to 01FFH). The stack pointers SP1 and SP2 change cy-
clically within their respective range: the range of SP1 is 0000H to 07FFH and the range of SP2 is 0000H 
to 00FFH. Therefore, pay attention to the SP1 value because it may be set to 0200H or more exceeding 
the 4-bit/16-bit accessible range in the S1C63616 or it may be set to 00FFH or less. Memory accesses ex-
cept for stack operations by SP1 are 4-bit data access. After initial reset, all the interrupts including NMI 
are masked until both the stack pointers SP1 and SP2 are set by software. Further, if either SP1 or SP2 is 
re-set when both are set already, the interrupts including NMI are masked again until the other is re-set. 
Therefore, the settings of SP1 and SP2 must be done as a pair.

Power control

(1)  When the power supply voltage booster/halver is turned on, the V

D2

 output voltage requires about 1 

msec to stabilize. Do not switch the power source for the voltage regulator (LCD system voltage regula-
tor) to V

D2

 until the stabilization time has elapsed.

(2)  HLON is prohibited from use, as it may cause malfunctions. Always be sure to set to "0".

(3)  Do not set DBON to "1" (boost mode) and VCSEL to "1" (driving with V

D2

) if the supply voltage V

DD

 

exceeds 2.5 V, as it may cause damage of the IC.

(4)  Current consumption increases in heavy load protection mode, therefore do not set heavy load protec-

tion mode with software if unnecessary.

Watchdog timer

When the watchdog timer is being used, the software must reset it within 3-second cycles. Because the 
watchdog timer is set in operation state by initial reset, set the watchdog timer to disabled state (not 
used) before generating an interrupt (NMI) if it is not used.

Oscillation circuit

(1)  When the high speed CPU operation is not necessary, you should operate the peripheral circuits accord-

ing to the setting outline indicate below. 

 

• CPU operating clock: 

OSC1

 

• OSC3 oscillation circuit:  Off 

 

(When the OSC3 clock is not necessary for some peripheral circuits.)

(2)  Since 1 msec to several tens of msec are necessary for the oscillation to stabilize after turning the OSC3 

oscillation circuit on. Consequently, you should switch the CPU operating clock (OSC1 

→

 OSC3) after 

allowing for a sufficient waiting time once the OSC3 oscillation goes on. (The oscillation start time will 
vary somewhat depending on the oscillator and on the externally attached parts. Refer to the oscillation 
start time example indicated in Chapter 7, "Electrical Characteristics".)

(3)  When switching the clock from OSC3 to OSC1, be sure to switch OSC3 oscillation off with separate 

instructions. Using a single instruction to process simultaneously can cause a malfunction of the CPU.

Summary of Contents for S1C63616







































































































































































































































Reviews:

No comments

Related manuals for S1C63616

Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Campbell NL115 Instruction Manual preview
NL115
Brand: Campbell Pages: 42
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Brand: Lattice Semiconductor Pages: 13
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Brand: Roland Pages: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Brand: Schrack Technik Pages: 2
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Brand: Intel Pages: 105
NAMCO SOUL CALIBUR II Manual preview
SOUL CALIBUR II
Brand: NAMCO Pages: 26
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
Ampro Corporation LITTLE BOARD P5X Hardware User Manual preview
LITTLE BOARD P5X
Brand: Ampro Corporation Pages: 121
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Brand: Buffalo Pages: 139
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18

Brands by name

Popular brands

Load more brands