Epson S1C63616 Technical Manual Download Page 90 | Manualshive

Page: 90 / 230

background image

SIC63616-(Rev. 1.0) NO. P83

3240-0412

IT0: 128 Hz interrupt factor flag (FFFEH•D0)
IT1: 64 Hz interrupt factor flag (FFFEH•D1)
IT2: 32 Hz interrupt factor flag (FFFEH•D2)
IT3: 16 Hz interrupt factor flag (FFFEH•D3)
IT4: 8 Hz interrupt factor flag (FFFFH•D0)
IT5: 4 Hz interrupt factor flag (FFFFH•D1)
IT6: 2 Hz interrupt factor flag (FFFFH•D2)
IT7: 1 Hz interrupt factor flag (FFFFH•D3)

These flags indicate the status of the clock timer interrupt.

When "1" is read:

Interrupt has occurred

When "0" is read:

Interrupt has not occurred

When "1" is written: Flag reset

When "0" is written: Invalid

The interrupt factor flags (IT0, IT1, IT2, IT3, IT4, IT5, IT6, IT7) correspond to the clock timer interrupts of
the respective frequencies (128 Hz, 64 Hz, 32 Hz, 16 Hz, 8 Hz, 4 Hz, 2 Hz, 1 Hz). The software can judge
from these flags whether there is a clock timer interrupt. However, even if the interrupt is masked, the flags
are set to "1" at the falling edge of the signal.
These flags are reset to "0" by writing "1" to them.
After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1") is
set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to reset (write
"1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt enabled state.
At initial reset, these flags are set to "0".

4.7.6 Programming notes

(1) Be sure to read timer data in the order of low-order data (TM0–TM3) then high-order data (TM4–TM7).

(2) The clock timer count clock does not synch with the CPU clock. Therefore, the correct value may not

be obtained depending on the count data read and count-up timings. To avoid this problem, the clock
timer count data should be read by one of the procedures shown below.

• Read the count data twice and verify if there is any difference between them.
• Temporarily stop the clock timer when the counter data is read to obtain proper data.

(3) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1")

is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to
reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt
enabled state.

«
...
88
89
90
91
92
...
»

Summary of Contents for S1C63616







































































































































































































































Reviews:

No comments

Related manuals for S1C63616

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Brand: IEI Technology Pages: 19

Brand: IEI Technology Pages: 87

Brand: IEI Technology Pages: 3

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: LaView Pages: 2

CloudGen Firewall

Brand: Barracuda Pages: 8

Brand: AMC Pages: 28

Brand: TP-Link Pages: 2

FaxFinder FF-120

Brand: Multitech Pages: 20

Brand: Jennic Pages: 14

Liebert ISWEBRT3

Brand: Emerson Pages: 28

PACSystems IC695CPE400

Brand: Emerson Pages: 37

Dixell iChill ICX207D

Brand: Emerson Pages: 20

Fisher FIELDVUE DLC3020f

Brand: Emerson Pages: 36

Liebert Intellislot Unity Card

Brand: Emerson Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands