manualshive.com logo in svg

Epson S1C63616, Technical Manual

The Epson S1C63616 Technical Manual is a comprehensive guide for users seeking detailed information about the product. This manual can be easily downloaded for free from manualshive.com, providing step-by-step instructions and valuable insights for optimal usage and troubleshooting. Get the most out of your Epson S1C63616 with this reliable manual.

Share
Download
background image

SIC63616-(Rev. 1.0) NO. P163

3240-0412

4.15 Interrupt and HALT/SLEEP

<Interrupt types>

The S1C63616 provides the following interrupt functions. 

External interrupt:  • Key input interrupt 

(8 systems) 

Internal interrupt:  • Watchdog timer interrupt 

(NMI, 1 system)

 

• Programmable timer interrupt 

(16 systems)

 

• Serial interface interrupt 

(1 system)

 

• Clock timer interrupt 

(8 systems)

 

• Stopwatch timer interrupt 

(4 systems)

 

• R/f converter interrupt 

(3 systems)

To authorize interrupt, the interrupt flag must be set to "1" (EI) and the necessary related interrupt mask 
registers must be set to "1" (enable). 
When an interrupt occurs the interrupt flag is automatically reset to "0" (DI), and interrupts after that are 
inhibited.

The watchdog timer interrupt is an NMI (non-maskable interrupt), therefore, the interrupt is generated 
regardless of the interrupt flag setting. Also the interrupt mask register is not provided. However, it is 
possible to not generate NMI since software can stop the watchdog timer operation.

Figure 4.15.1 shows the configuration of the interrupt circuit. 

Note:  After an initial reset, all the interrupts including NMI are masked until both the stack pointers SP1 

and SP2 are set with the software. Be sure to set the SP1 and SP2 in the initialize routine.

 

Further, when re-setting the stack pointer, the SP1 and SP2 must be set as a pair. When one of them 
is set, all the interrupts including NMI are masked and interrupts cannot be accepted until the other 
one is set.

<HALT/SLEEP>

The S1C63616 has the HALT and SLEEP functions that considerably reduce current consumption when it is 
not necessary.
The CPU enters HALT status when the HALT instruction is executed. In HALT status, the operation of the 
CPU is stopped. However, timers continue counting since the oscillation circuit operates. Reactivating the 
CPU from HALT status is done by generating a hardware interrupt request including NMI.

When the CPU enters SLEEP status as the result of the SLP instruction, the CPU stops its operation and 
the OSC1 and OSC3 oscillation circuits are also stop. Therefore, the power supply voltage booster/halver 
cannot generate V

D2

 in SLEEP mode. If it is used V

D2

 to drive the LCD system voltage regulator, it is 

necessary to switch V

DD

 before executing the SLP instruction. And to prevent improper operation after the 

CPU wakes up, be sure to run the CPU with the OSC1 clock before setting the CPU in the SLEEP mode.
Reactivating from SLEEP status can only be done by generation of a key input interrupt request from a P1x 
or P4x port.
Therefore, set and confirm the P1(4)x input level, the flag and the registers for the P1(4)x port, the CPU 
clock, and the power control according to the following procedures to be used to enter/cancel SLEEP status 
before executing the SLP instruction surely.

1.  LCD system voltage regulator power source switch register VCSEL="0"

 

Power supply voltage booster/halver boost mode On/Off register DBON="0"

 

(LCD system voltage regulator is driven with V

DD

)

2.  CPU system clock switching register CLKCHG = "0" (OSC1 CPU clock is selected)

3.  Interrupt selection register SIPxx = "1" (the Pxx input port interrupt is selected)

4.  Interrupt mask register EIKxx = "1" (the Pxx input port interrupt is enabled)

Summary of Contents for S1C63616







































































































































































































































Reviews:

No comments

Related manuals for S1C63616

Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Brand: DCB Pages: 28
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
Technics SH-GE90 Service Manual preview
SH-GE90
Brand: Technics Pages: 20
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
Sony Ericsson Developer's Board Manual preview
Developer's Board
Brand: Sony Ericsson Pages: 28
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
DigiTech RP 3 User Manual preview
RP 3
Brand: DigiTech Pages: 28
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Brand: Promise Technology Pages: 148
DAPAudio D2081 Manual preview
D2081
Brand: DAPAudio Pages: 33
BOSER Technology HS-4703 Manual preview
HS-4703
Brand: BOSER Technology Pages: 78
Paradyne MIM-4T1 Installation Instructions Manual preview
MIM-4T1
Brand: Paradyne Pages: 10
Motorola MC68VZ328 User Manual preview
MC68VZ328
Brand: Motorola Pages: 376
Motorola MC68341 User Manual preview
MC68341
Brand: Motorola Pages: 20
Hitachi DS120 G2 Hardware Manual preview
DS120 G2
Brand: Hitachi Pages: 17
Hitachi LQE050 Hardware Manual preview
LQE050
Brand: Hitachi Pages: 53
Hitachi G-SPEED ES PRO Installation Manual preview
G-SPEED ES PRO
Brand: Hitachi Pages: 23

Brands by name

Popular brands

Load more brands