manualshive.com logo in svg

ENSTROM 280FX Series, Operator'S Manual

The ENSTROM 280FX Series Pilot's Manual is a comprehensive and indispensable resource for all pilots operating this remarkable aircraft. This manual is available for free download from manualshive.com, providing easy access to essential information, procedures, and specifications, enhancing flight safety and efficiency.

Share
Download
background image

     

ENSTROM 280FX OPERATOR’S MANUAL 

8-11 

 

 

 

 

Rev. 6 

Report No. 28-AC-020 

 

Feb 21/12 

 

  b.  Battery – Servicing 

      Refer to the battery manufacturer’s instructions for 

servicing the battery. 

CAUTION 

To clean spilled electrolyte off battery, mix one 

part baking soda to three parts water. DO NOT 
allow solution to enter battery cells. Rinse with 
clear water and wipe off with clean cloth. 

4.  Main Transmission Location 

  The main transmission is located aft of the cabin section, 

mounted on the pylon above the engine. Power is 
transmitted to the main and tail rotor assemblies. Oil level 
is checked by a sight gauge located on the right, aft side 

of the transmission. The top step kick-in panel on the 
right side of the helicopter can be opened for the 
inspection. With the helicopter in a relatively level 

position, the oil level should be at or near the halfway level 
in the sight gauge. 

  The main rotor transmission oil capacity is 6 pints.  When 

the oil is drained from the transmission, only 5.5 pints of 

oil are required for servicing the transmission.  Refer to 
Table 8-2 for the approved oils for servicing the main rotor 
transmission. 

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical 

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision 

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Reviews:

No comments

Related manuals for 280FX Series

Faller 564 Manual preview
564
Brand: Faller Pages: 4
Eduard He 111H-6 nose interior Quick Start Manual preview
He 111H-6 nose interior
Brand: Eduard Pages: 6
Fisher-Price KICK`N CRAWL BARN 71699 Instructions preview
KICK`N CRAWL BARN 71699
Brand: Fisher-Price Pages: 4
Jamara Little Home 460498 Instruction Manual preview
Little Home 460498
Brand: Jamara Pages: 4
VQ Radio Control Model PICHLER Beechcraft T-34C TURBO MENTOR Instruction Manual preview
PICHLER Beechcraft T-34C TURBO MENTOR
Brand: VQ Radio Control Model Pages: 12
Jamara Lucky Instruction preview
Lucky
Brand: Jamara Pages: 8
Faller 2 BEEKEEPER'S TRAILERS Instructions Manual preview
2 BEEKEEPER'S TRAILERS
Brand: Faller Pages: 8
Hasbro Transformers 83621 Instruction Manual preview
Transformers 83621
Brand: Hasbro Pages: 1
PIKO 52690 52691 Instructions For Use Manual preview
52690 52691
Brand: PIKO Pages: 12
Littlebits GIZMOS & GADGETS Manual preview
GIZMOS & GADGETS
Brand: Littlebits Pages: 13
Eduard Zoom RA-5C Vigilante Quick Start Manual preview
Zoom RA-5C Vigilante
Brand: Eduard Pages: 2
Tadano AC 7.450-1 Build Manual preview
AC 7.450-1
Brand: Tadano Pages: 16
VTech Switch & Go Dinos Seeker the T-Rex Parents' Manual preview
Switch & Go Dinos Seeker the T-Rex
Brand: VTech Pages: 11
LGB 26420 Instruction Manual preview
26420
Brand: LGB Pages: 12
Jamara Fokker DVII Instruction preview
Fokker DVII
Brand: Jamara Pages: 28
Himoto Stealth Interceptor ST745 Instruction Manual preview
Stealth Interceptor ST745
Brand: Himoto Pages: 12
Team Losi Micro-T Operation Manual preview
Micro-T
Brand: Team Losi Pages: 7
Avios SPITFIRE MK1a Instruction Manual preview
SPITFIRE MK1a
Brand: Avios Pages: 34

Brands by name

Popular brands

Load more brands