manualshive.com logo in svg

ENSTROM 280FX Series, Operator'S Manual

The ENSTROM 280FX Series Pilot's Manual is a comprehensive and indispensable resource for all pilots operating this remarkable aircraft. This manual is available for free download from manualshive.com, providing easy access to essential information, procedures, and specifications, enhancing flight safety and efficiency.

Share
Download
background image

10-4-4 

ENSTROM 280FX OPERATOR’S MANUAL 

FAA Approved: Mar 26/12 

Rev. 6 

Report No. 28-AC-020 

Feb 21/12 

SECTION VI. WEIGHT AND BALANCE 

A new weight and balance should be calculated per the 

instructions in Section 6 of the Basic Rotorcraft Flight 
Manual using the following information: 

Table 10-4-1. Weight and Balance Information 

ITEM 

WEIGHT 

(lb) 

ARM 

(in) 

MOMENT 

(in-lb) 

Snowshoe Kit 

18.0 

100.9 

1816.2 

 

 

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical 

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision 

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Reviews:

No comments

Related manuals for 280FX Series

Laser Pegs 1070 Instruction Manual preview
1070
Brand: Laser Pegs Pages: 3
Laser Pegs 1070 Instructions preview
1070
Brand: Laser Pegs Pages: 2
Rage SPINNER MISSILE XL Instructions preview
SPINNER MISSILE XL
Brand: Rage Pages: 2
Faller DODGEM CAR RIDE Instructions Manual preview
DODGEM CAR RIDE
Brand: Faller Pages: 12
Zipp Manufacturing PRO VEE Full Race Mono Hull Building Instructions preview
PRO VEE Full Race Mono Hull
Brand: Zipp Manufacturing Pages: 45
RVE PHECDA E680 Instruction Manual preview
PHECDA E680
Brand: RVE Pages: 36
Rail King Royal Hudson Steam Engine Operating Instructions Manual preview
Royal Hudson Steam Engine
Brand: Rail King Pages: 24
Rail King Union Pacific 2-8-0 Operation Manual preview
Union Pacific 2-8-0
Brand: Rail King Pages: 31
Faller BUILDING SITE DECORATION Quick Start Manual preview
BUILDING SITE DECORATION
Brand: Faller Pages: 4
LeapFrog 6135 Instruction Manual preview
6135
Brand: LeapFrog Pages: 13
Carrera RC 37050000 Assembly And Operating Instructions Manual preview
37050000
Brand: Carrera RC Pages: 40
Eduard Lancaster landing flaps Quick Start Manual preview
Lancaster landing flaps
Brand: Eduard Pages: 2
World Tech Toys RC Creatures Gorilla Instruction Manual preview
RC Creatures Gorilla
Brand: World Tech Toys Pages: 4
DICKIE TOYS Despicable Me 2 20 112 0005 Operating Instructions Manual preview
Despicable Me 2 20 112 0005
Brand: DICKIE TOYS Pages: 16
The Land of Nod Street Vendor Cart Assembly Instructions preview
Street Vendor Cart
Brand: The Land of Nod Pages: 5
Nine Eagles Solo Pro 100D 3D User Manual preview
Solo Pro 100D 3D
Brand: Nine Eagles Pages: 18
m2model Discovery micro Assembly Instructions preview
Discovery micro
Brand: m2model Pages: 3
JMB-Jets Boeing TX/ T7A Instructions Manual preview
Boeing TX/ T7A
Brand: JMB-Jets Pages: 15

Brands by name

Popular brands

Load more brands