ENSTROM 280FX Series Operator'S Manual Download Page 37

Page: 37 / 246

ENSTROM 280FX OPERATOR’S MANUAL

2-15

FAA Approved: Feb 11/13

Rev. 8

Report No. 28-AC-020

Jan 7/13

2. This placard is to be placed in the baggage compartment.

MAXIMUM WEIGHT IN THIS COMPARTMENT IS
108 LBS. OBSERVE C.G. AND GROSS WEIGHT
LIMITATIONS

3. This placard is to be placed on the clutch handle.

STOW FLAT ON FLOOR BEFORE FLIGHT

4. This placard is to be placed near the door handle.

EMERGENCY EXIT

PULL DOOR HANDLE TO OPEN CABIN DOOR

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Search results

Summary of Contents for 280FX Series

Reviews:

Related manuals for 280FX Series

Brands by name

Popular brands

ENSTROM 280FX Series, Operator'S Manual

Search results

Summary of Contents for 280FX Series

Reviews:

Related manuals for 280FX Series

Brands by name

Popular brands