ENSTROM 280FX Series Operator'S Manual Download Page 142

Page: 142 / 246

8-8

ENSTROM 280FX OPERATOR’S MANUAL

Rev. 6

Report No. 28-AC-020

Feb 21/12

Table 8-1. Engine Oil Recommendations

TEMPERATURE

MIL-L-22851 OR SAEJ1899 ASHLESS

DISPERSANT GRADE

All Temperature

SAE15W50 or SAE20W50

Above 80°F

SAE60

Above 60°F

SAE40 or SAE50

30°F to 90°F

SAE 30

0°F to 70°F

SAE30, SAE40, or SAE20W40

0°F to 90°F

SAE20W50 or SAE15W50

Below 10°F

SAE30 or SAE20W50

b. Draining – Engine Oil System

(1) Place suitable container under belly panel.

(2) Remove drain plug or open the drain valve and

allow oil to drain.

(3) Disconnect a hose from the engine oil coolers and

allow oil to drain.

NOTE

Engine oil should be warm, and a sufficient
amount of time should be allowed for complete
drainage of sump.

(4) Connect the hose after draining the oil.

(5) Reinstall the drain plug and safety wire or close the

drain valve.

c. Replacement of Engine Oil Filter (P/N CH48103)

A spin-on type oil filter is located on the accessory

housing. The filter should be replaced at each oil change.
To replace the filter, follow the procedure below.

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Search results

Summary of Contents for 280FX Series

Reviews:

Related manuals for 280FX Series

Brands by name

Popular brands

ENSTROM 280FX Series, Operator'S Manual

Search results

Summary of Contents for 280FX Series

Reviews:

Related manuals for 280FX Series

Brands by name

Popular brands