manualshive.com logo in svg

ENSTROM 280FX Series, Operator'S Manual

The ENSTROM 280FX Series Pilot's Manual is a comprehensive and indispensable resource for all pilots operating this remarkable aircraft. This manual is available for free download from manualshive.com, providing easy access to essential information, procedures, and specifications, enhancing flight safety and efficiency.

Share
Download
background image

6-8 

 

ENSTROM 280FX OPERATOR’S MANUAL 

   

 

Rev. 

11 

Report No. 28-AC-020 

 

Sep 20/17 

 

(1) Moments obtained by multiplying weight times arm or from 
Loading Chart, Figure 6-4. 

  (2) The longitudinal c.g. relative to the datum line is found by 

dividing the moment by the weight. 

 

    c.g. zero fuel = 

= 92.2 inches 

 

    c.g. full fuel = 

= 92.6 inches 

 

 

The total weight and moment can also be plotted on Figure 
6-5 to determine if the loading is within longitudinal limits. 

 

(3) Total weight not to exceed 2600 lb. 

 

3.  Sample Calculation – Lateral Offset Moment 

 Sample 

Helicopter 

 

SAMPLE LOADING 

Arm  

(in) 

Weight 

(lb) 

Moment 

(in-lb) 

a.  Pilot (left seat) 

-13.5 

170 

-2295 

b.  Passenger (center seat) 

+3.0 

140 

+420 

c.  Passenger (right seat) 

+20.5 

170 

+3485 

d. Total 

   +1610 

 

  a.  Plot 2350 lb and +1610 in-lb on Figure 6-2 to ensure 

moment is in approved area. 

 

194,600 in-lb 

2110.0 lb 

217,600 in-lb 

2350.0 lb 

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical 

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision 

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Reviews:

No comments

Related manuals for 280FX Series

J-Power P51 Assembly And Operating Instructions Manual preview
P51
Brand: J-Power Pages: 32
Baghera 1933 Assembly Instructions preview
1933
Brand: Baghera Pages: 4
FB Jets Dolphin S Assembly Manual preview
Dolphin S
Brand: FB Jets Pages: 39
Eduard SM-79 Sparviero Exterior Quick Start Manual preview
SM-79 Sparviero Exterior
Brand: Eduard Pages: 4
Connoisseur Models train Instruction Booklet preview
train
Brand: Connoisseur Models Pages: 14
PARKZONE Ultra Micro Pole Cat Instruction Manual preview
Ultra Micro Pole Cat
Brand: PARKZONE Pages: 18
ROBBE ARROW PLUS TRAINER EVOLUTION Operating Instructions Manual preview
ARROW PLUS TRAINER EVOLUTION
Brand: ROBBE Pages: 20
WARCRADLE STUDIOS DYSTOPIAN WARS TIANLONG BATTLEFLEET Assembly Instructions preview
DYSTOPIAN WARS TIANLONG BATTLEFLEET
Brand: WARCRADLE STUDIOS Pages: 4
Faller 293059 Assembly Instructions Manual preview
293059
Brand: Faller Pages: 12
Eduard B-17E/F engines Quick Start Manual preview
B-17E/F engines
Brand: Eduard Pages: 2
Monogram 0067 85006700200 Manual preview
0067 85006700200
Brand: Monogram Pages: 33
LEGO ARCHITECTURE BIG BEN Building Instructions preview
ARCHITECTURE BIG BEN
Brand: LEGO Pages: 68
GAUGEMASTER Fordhampton Farm House Manual preview
Fordhampton Farm House
Brand: GAUGEMASTER Pages: 4
Hasbro Star Wars Electronic Ask Yoda 72410 Instruction Manual preview
Star Wars Electronic Ask Yoda 72410
Brand: Hasbro Pages: 4
LEGO Super Mario Adventures with Peach Quick Start Manual preview
Super Mario Adventures with Peach
Brand: LEGO Pages: 24
Velleman KNS2 User Manual preview
KNS2
Brand: Velleman Pages: 9
LGB 21431 Manual preview
21431
Brand: LGB Pages: 32
Playskool Tonka Construction Kit On the Go 05513 Instruction Manual preview
Tonka Construction Kit On the Go 05513
Brand: Playskool Pages: 4

Brands by name

Popular brands

Load more brands