manualshive.com logo in svg

ENSTROM 280FX Series, Operator'S Manual

The ENSTROM 280FX Series Pilot's Manual is a comprehensive and indispensable resource for all pilots operating this remarkable aircraft. This manual is available for free download from manualshive.com, providing easy access to essential information, procedures, and specifications, enhancing flight safety and efficiency.

Share
Download
background image

2-6 

 

ENSTROM 280FX OPERATOR’S MANUAL 

FAA Approved: Mar 26/12 

 

Rev. 6 

Report No. 28-AC-020 

 

Feb 21/12 

NOTE 

Takeoffs and landings at 2350 lb gross weight were 

demonstrated to 10,000 ft density altitude in all 
wind conditions up to 15 MPH. 

NOTE 

Operators should use appropriate caution above 
10,000 ft density altitude and in winds greater than 

15 MPH to ensure safe takeoffs and landings. 

2-6. Rotor RPM 

1.  Flight limitations power on: 

Minimum 334 

RPM 

Maximum 351 

RPM 

2.  Flight limitations power off: 

Minimum 334 

RPM 

Maximum 385 

RPM 

3.  Reference Section 8 for adjustment procedures. 

NOTE 

During transient maneuvers, such as simulated 
power failure during pilot training, the rotor RPM 

may fall below 334. These maneuvers have been 
demonstrated with rotor RPM dropping briefly to 
280; however, sufficient time and altitude must be 

available to regain RPM. 

NOTE 

The helicopter is equipped with a rotor RPM warning 

device. Operating the helicopter below 334 RPM with 
the collective off the down stop will automatically 
activate a warning horn. 

 

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical 

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision 

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Reviews:

No comments

Related manuals for 280FX Series

Kadee 103 General Instructions preview
103
Brand: Kadee Pages: 2
Jamara Ranger Instructions Manual preview
Ranger
Brand: Jamara Pages: 28
Radica Games 75071 Instruction Manual preview
75071
Brand: Radica Games Pages: 2
Mardave V12-CE Setup Manual preview
V12-CE
Brand: Mardave Pages: 12
Hacker Model LUNAK SKG Series Manual preview
LUNAK SKG Series
Brand: Hacker Model Pages: 16
LEGO STAR WARS 75135 Building Instructions preview
STAR WARS 75135
Brand: LEGO Pages: 71
Viessmann 4264 Operation Manual preview
4264
Brand: Viessmann Pages: 4
Fisher-Price Cadillac ESCALADE H044040 Owner'S Manual & Assembly Instructions preview
Cadillac ESCALADE H044040
Brand: Fisher-Price Pages: 36
TWM 1/4 Clipped Wing Cub Instruction Manual preview
1/4 Clipped Wing Cub
Brand: TWM Pages: 20
Horejsi Long Shot 3 Building Instructions preview
Long Shot 3
Brand: Horejsi Pages: 5
Opitec Hobbyfix Manual preview
Hobbyfix
Brand: Opitec Pages: 11
K'Nex Doubledare Dueling Coaster Manual preview
Doubledare Dueling Coaster
Brand: K'Nex Pages: 44
VTech 80-072300 - Little Einsteins Learn User Manual preview
80-072300 - Little Einsteins Learn
Brand: VTech Pages: 14
PREZIOSI KOKUYO Flair Klixi Mixi Manual preview
KOKUYO Flair Klixi Mixi
Brand: PREZIOSI Pages: 6
Fisher-Price CBJ32 Instructions Manual preview
CBJ32
Brand: Fisher-Price Pages: 10
Fisher-Price 77198 Instructions Manual preview
77198
Brand: Fisher-Price Pages: 20
AeroWorks 50cc P-51D Mustang ARF-QB Assembly Manual preview
50cc P-51D Mustang ARF-QB
Brand: AeroWorks Pages: 85
Lionel Tie Car Owner'S Manual preview
Tie Car
Brand: Lionel Pages: 8

Brands by name

Popular brands

Load more brands