manualshive.com logo in svg

ENSTROM 280FX Series, Operator'S Manual

The ENSTROM 280FX Series Pilot's Manual is a comprehensive and indispensable resource for all pilots operating this remarkable aircraft. This manual is available for free download from manualshive.com, providing easy access to essential information, procedures, and specifications, enhancing flight safety and efficiency.

Share
Download
background image

10-2-12 

ENSTROM 280FX OPERATOR’S MANUAL 

FAA Approved: Mar 26/12 

Rev. 6 

Report No. 28-AC-020 

Feb 21/12 

 

NOTE 

This includes the normal ambient temperature 
variations associated with changes in altitude. 

2. For flights to higher altitude – 10,000 ft differential 

altitude permitted (provided float pressure is not more 

than 1.5 psig at takeoff). 

3. For variations in ambient air temperature and/or water 

temperature at a given base altitude use the following 
procedure. When an ambient air temperature or water 
temperature colder than the temperature at initial 

inflation is anticipated, over inflate, 0.5 psig above normal 
for each 15°F decrease in temperature anticipated. 

 

This electronic document is not linked to a subscription for revision control or distribution. Refer to theTechnical 

Publications Status link under the Technical Support Page of the Enstrom Helicopter website for the current revision 

level of the 280FX Rotorcraft Flight Manual.

UNCONTROLLED COPY WHEN DOWNLOADED OR PRINTED

Summary of Contents for 280FX Series























































































































































































































































Reviews:

No comments

Related manuals for 280FX Series

Talk To Me Technologies wego A Quick Start Manual preview
wego A
Brand: Talk To Me Technologies Pages: 2
Talk To Me Technologies wego A User Manual preview
wego A
Brand: Talk To Me Technologies Pages: 16
Air Hogs Tow Mate Instruction Manual preview
Tow Mate
Brand: Air Hogs Pages: 6
Eduard Spitfire placards Manual preview
Spitfire placards
Brand: Eduard Pages: 3
E-FLITE EFLH2200 Instruction Manual preview
EFLH2200
Brand: E-FLITE Pages: 19
WARCRADLE STUDIOS WILD WEST EXODUS VENGEANCE OF THE EARPS Assembly Instructions preview
WILD WEST EXODUS VENGEANCE OF THE EARPS
Brand: WARCRADLE STUDIOS Pages: 5
Goblin 380 KYLE STACY EDITION User Manual preview
380 KYLE STACY EDITION
Brand: Goblin Pages: 39
VTech Megaphone Mission Voice Changer Parents' Manual preview
Megaphone Mission Voice Changer
Brand: VTech Pages: 12
Tabletop Scenics KRTS092 Assembly Instruction Manual preview
KRTS092
Brand: Tabletop Scenics Pages: 12
Jamara Parkhaus Small City Instructions preview
Parkhaus Small City
Brand: Jamara Pages: 4
Hasbro Transformers Animated Starscream 83469/83463 Instruction Manual preview
Transformers Animated Starscream 83469/83463
Brand: Hasbro Pages: 1
K'Nex IMAGINE SUPER VALUE TUB Manual preview
IMAGINE SUPER VALUE TUB
Brand: K'Nex Pages: 28
ZAGI 400 ELECTRIC Assembly Manual preview
400 ELECTRIC
Brand: ZAGI Pages: 17
REVELL MONOGRAM SHELBY COBRA 427 S/C Assembly Manual preview
MONOGRAM SHELBY COBRA 427 S/C
Brand: REVELL Pages: 12
Fisher-Price Baby GymTasTics Zebra K0317 Instruction Sheet preview
Baby GymTasTics Zebra K0317
Brand: Fisher-Price Pages: 6
JR Robinson R22 Assembly Instructions Manual preview
Robinson R22
Brand: JR Pages: 76
Hasbro Disney Moana Spin & Swim Quick Start Manual preview
Disney Moana Spin & Swim
Brand: Hasbro Pages: 2
Barbie LIL' TRAIL RIDER Owner'S Manual With Assembly Instructions preview
LIL' TRAIL RIDER
Brand: Barbie Pages: 20

Brands by name

Popular brands

Load more brands