Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 53

Page: 53 / 63

Section 40

00-02-0787

2015-03-23

~ 45 ~

REGISTER

TYPE

DESCRIPTION

40001

Read Only

Running Hours, upper byte.

40002

Read Only

Running hours, lower byte.

40003

Read Only

Engine RPM

40004

Read Only

Battery Voltage. (12.5 will read 125)

40005

Read Only

Oil Pressure.

40006

Read Only

Engine Temperature.

40007

Read Only

System Status: Bits description follows:

Bit 0

(LSB) Auto Ready: (1) yes, (0) no.

Bit 1

Prestart Timing: (1) yes, (0) no.

Bit 2

Start Delay Timing: (1) yes, (0) no.

Bit 3

Warm-up Delay Timing: (1) yes, (0) no.

Bit 4

Fill Mode: (1) yes, (0) no.

Bit 5

At Load: (1) yes, (0) no.

Bit 6

Stop Delay Timing: (1) yes, (0) no.

Bit 7

Cooldown Delay Timing: (1) yes, (0)
no.

Bit 8

Common Failure: (1) yes, (0) no.

Bit 9

Spare.

Bit 10 Spare.

Bit 11 Spare.

Bit 12 Spare.

Bit 13 Spare.

Bit 14 Spare.

Bit 15 (MSB) Spare.

Summary of Contents for Murphy EMS PRO LITE
































































Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Related manuals for Murphy EMS PRO LITE

Brands by name

Popular brands

Enovation Controls Murphy EMS PRO LITE, Installation And Operation Manual

Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Related manuals for Murphy EMS PRO LITE

Brands by name

Popular brands