Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 59

Page: 59 / 63

Section 40

00-02-0787

2015-03-23

~ 51 ~

Specifications

Operating Voltage:

8 VDC Minimum to 14.4 VDC Maximum (Designed

to work on 12 VDC systems).

Operating Temperature:

-40

to 80°C (-40 to 176°F)

Storage Temperature:

-40° to 80°C (-40° to 176°F)

Environmental Sealing

: IP65

Relative Humidity:

95%RH @ 60°F (140°C)

Standby Current:

140mA @ 12VDC for standby current. 600mA Max @

12VDC when not in standby.

CAN Bus:

SAE J1939 Compliant

Enclosure:

Polycarbonate NEMA 4 (UL/cUL listed)

Analog Inputs:

6 Analog Inputs designated via program; sender/ground

digital 4-20mA, 0-5 VDC.

Digital Inputs

: 4 Digital Inputs high/low (Both and ground are

detected as active inputs. An inactive input floats at approximately 1/2
B+).

Frequency

: 1 optically isolated input for speed reference, magnetic pick-

up, (2VAC-50VAC RMS, 30-10kHz).

Fuel Sender Input

: 33 Ohm full, 240 Ohm empty

Analog Output

: 4-20mA or .4 to 4.2VDC (used for .4 – 4.2V throttling)

Digital Outputs

: 6 Digital Outputs; 3 FET B+ (rated at 1A), 3 Open

Collector sink-to-ground 100 mA (one of these is used to pilot a relay)

User Interface

: 8-button keypad, Graphical display, back-lit.

Communications

: RS485, RS232, CAN J1939, CAN 2.0B ports

Shipping Weight

: 7 lb. (3.2 kg)

Shipping Dimensions

: 12x12x10 (304.8x304.8x254 mm)

Real-time Clock

: 24hr Format

Summary of Contents for Murphy EMS PRO LITE
































































Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Related manuals for Murphy EMS PRO LITE

Brands by name

Popular brands

Enovation Controls Murphy EMS PRO LITE, Installation And Operation Manual

Search results

Summary of Contents for Murphy EMS PRO LITE

Reviews:

Related manuals for Murphy EMS PRO LITE

Brands by name

Popular brands