Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 17 | Manualshive

Page: 17 / 63

background image

Section 40

00-02-0787

2015-03-23

~ 9 ~

Pressure Start/Stop Type

The Pressure Start/Stop Type allows you to automatically start and stop
the engine using a pressure transducer to measure low and high set
points. Follow the steps below to set this start/stop feature.

1.

Access the S Menu by pressing

[Menu]

.

2.

Press the

[Up or Down Arrow]

to scroll to the correct

Entry Code (See Entry Code Supplement, page 48).

3.

Press the

[Up or Down Arrow]

until (S35) SRT/STP

SEL is displayed and press

[Enter]

.

4.

Press the

[Up Arrow]

until TRANSDUCER is

highlighted and press

[Enter]

.

5.

Press the

[Up Arrow]

until (S37) XDUCER TYPE is

displayed and press

[Enter]

.

6.

Press the

[Up Arrow]

until PRESSURE CONTROL is

highlighted and press

[Enter]

.

7.

Review and modify the settings for S-numbers S45
through S56 for Pressure Start/Stop Type. To modify,
press

[Enter]

while the setting is highlighted. When

finished with the modification, press

[Enter]

again.

Refer to the S-Number table in

Menus

for a

description of the S-Numbers settings.

8.

When finished with the S45 through S56 settings,
press

[Menu]

to exit.

Level Start/Stop Type

The Level Start/Stop Type allows you to automatically start and stop the
engine using a level transducer to measure low and high set points.
Follow the steps below to set this start/stop feature.

1.

Access the S Menu by pressing

[Menu]

.

2.

Press the

[Up or Down Arrow]

to scroll to the correct

Entry Code (See Entry Code Supplement for Entry
Codes).

3.

Press the

[Up or Down Arrow]

until (S35) SRT/STP

SEL is displayed and press

[Enter]

.

4.

Press the

[Up Arrow]

until TRANSDUCER is

highlighted and press

[Enter]

.

5.

Press the

[Up Arrow]

until (S37) XDUCER TYPE

displays and press

[Enter]

.

6.

Press the

[Up Arrow]

until LEVEL CONTROL is

highlighted and press

[Enter]

.

«
...
15
16
17
18
19
...
»

Summary of Contents for Murphy EMS PRO LITE
































































Reviews:

No comments

Related manuals for Murphy EMS PRO LITE

Brand: KEENZ Pages: 24

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: 3M Pages: 34

Brand: janitza Pages: 58

Brand: NEC Pages: 30

Brand: Vageo Pages: 2

MagicSpeed Series

Brand: Waeco Pages: 76

Brand: Brand Innovations Pages: 56

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

Brand: Woodward Pages: 32

Lux Intelligent

Brand: Advanced Pages: 62

Brand: intech 21 Pages: 15

Brand: Xsens Pages: 17

Brand: Barco Pages: 4

STRATOSTM INSPIRE

Brand: Ultrahaptics Pages: 7

Brand: ICP DAS USA Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands