manualshive.com logo in svg

Enovation Controls Murphy EMS PRO LITE, Installation And Operation Manual

Share
Download
Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 48

 

Section 40 

00-02-0787 

2015-03-23

 

~ 40 ~

 

Digital 

Output 

Description 

Connector 

1 

Fuel/Ignition/ECU Enable (B+) 

Pin G, 21 Pos. Conn. from 
R1 relay 

2 

Reserved 

 

3 

Alt Excite (B+)

 

 

4 

Throttle Decrease (Murphy Throttle 
Actuator AT-03069)

 

Pin R, 21 Pos. Conn

 

5 

Throttle Increase ((Murphy Throttle 
Actuator AT-03069)

 

Pin S 21 Pos. Conn

 

6 

Reserved 

 

7 

Reserved 

 

8 

Prestart (B-)

 

Pin E, 9 Pos Conn

 

9 

Reserved 

 

10 

Crank (B+)

 

Pin D, 21 Pos. Conn. from 
R2 relay

 

11 

Reserved 

 

12 

Reserved 

 

PCBA Shunts 

Reference this section for default positions of the Shunt Jumpers on the 
PCBA’s. 

RS485 Terminating Resistor (LK3 Shunt): 

This shunt allows a terminating resistor to be used on the RS485 port. 
(Default ON)  

•

 

ON – (Jumper Installed) allows the terminating resistor to be 
present. 

•

 

OFF – (Jumper Removed) removes terminating resistor from the 
RS485.  

 
Sender Shunt (LK5 Shunt): 

This shunt controls sender power (Default ON). This shunt must be 
installed to use senders. It can be removed when no senders are being 
used to reduce heat buildup inside the controller. This is only of interest 
in systems with battery voltage of 12VDC. 

•

 

ON – (Jumper Installed) allows sender resistor power for 
Mechanical engines using senders. 

•

 

OFF – (Jumper Removed) When the program is not using 
senders, this shunt can be removed. 

 
 

Summary of Contents for Murphy EMS PRO LITE
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands