Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 14 | Manualshive

Page: 14 / 63

background image

Section 40

00-02-0787

2015-03-23

~ 6 ~

Screens Displayed

Screen Name

Description

LEVEL XX.X

(IF SELECTED)

This displays the current system level as sensed from a
transducer.

LOCAL THROT

(IF SELECTED)

This is only show if Local Throttle is selected in S-34.

SOOT LEVEL

(IF SELECTED)

This shows the soot level percentage from SPN 3719.
There are also 3 alarms associated with this Status
sent from the ECU. The Alarms will be displayed on the
Alarm line as “SOOT LEVEL LOW”, “SOOT LEVEL
MEDIUM”, or “SOOT LEVEL HIGH”.

UREA LEVEL

(IF SELECTED)

This shows the urea level percentage from SPN 1761.

FIRST FOUR-UP
SCREEN

(DEFAULT SCREEN)

The first four-up screen should display Engine Oil
Pressure, Engine Coolant Temp,

Battery Voltage, &

Engine RPM. This is the default screen when powering
up the controller.

SECOND FOUR-UP
ELECTRONIC ONLY
SCREEN

The second four-up screen should display Run Hours,
Fuel Consumption, Engine Load %, & Engine RPM. This
screen can be viewed by pressing the arrow up key from
the default screen.

SHUTDOWN
SCREEN

This screen shows the last five shutdowns that have
occurred. This screen can be accessed by pressing the
arrow up key past the four-up screen(s).

«
...
12
13
14
15
16
...
»

Summary of Contents for Murphy EMS PRO LITE
































































Reviews:

No comments

Related manuals for Murphy EMS PRO LITE

Brand: Access Pages: 12

Brand: Badger Basket Pages: 3

Brand: BADLANDS Pages: 2

Brand: Daikin Pages: 56

Brand: Danfoss Pages: 36

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: VAT Pages: 27

MorphoAccess SIGMA Extreme Series

Brand: Idemia Pages: 31

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brand: MAKOT Pages: 6

Brand: Bartlett Pages: 7

Brand: Polycom Pages: 2

Brand: Baninni Pages: 5

Brand: WAGNER Pages: 128

OPTISWITCH 5100 C

Brand: KROHNE Pages: 40

Brand: BEBE CONFORT Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands