manualshive.com logo in svg

Enovation Controls Murphy EMS PRO LITE, Installation And Operation Manual

Share
Download
Enovation Controls Murphy EMS PRO LITE Installation And Operation Manual Download Page 42

 

Section 40 

00-02-0787 

2015-03-23

 

~ 34 ~

 

P-

Number 

Name 

Description 

P4 

WED SEL 

Set this to YES if you want to start your 
engine on WEDNESDAY.  Set it to NO if you 
want to lock out the start time on this day.  

Factory set to NO.

 

P5 

THR SEL 

Set this to YES if you want to start your 
engine on THURSDAY.  Set it to NO if you 
want to lock out the start time on this day.  

Factory set to NO.

 

P6 

FRI SEL 

Set this to YES if you want to start your 
engine on FRIDAY.  Set it to NO if you want 
to lock out the start time on this day.  

Factory set to NO.

 

P7 

SAT SEL 

Set this to YES if you want to start your 
engine on SATURDAY.  Set it to NO if you 
want to lock out the start time on this day.  

Factory set to NO.

 

P8 

CLK A RUN TM 

This set-point lets you set in the amount of 
time you would like your engine to run on 
your first start time.  You have three available 
start times per day (A, B, and C).  

Factory 

set to 0.0.

 

P9 

CLK A HR 

This set-point lets you set the clock hour you 
would like to start in 24hr format.  For 
example, if you want to start in the 3 o'clock 
in the afternoon hour, set it to 15.  

Factory 

set to 00.

 

P10 

CLK A MIN 

This set-point lets you set the clock minute 
you would like to start.  For example, if you 
want to start at 8:30 in the morning, you 
would adjust this until it read 30 in the minute 
portion 

Factory set to 00.

 

P11 

CLK B RUN TM 

This set-point lets you set in the amount of 
time you would like your engine to run on 
your first start time.  You have three available 
start times per day (A, B, and C).  

Factory 

set to 0.0.

 

P12 

CLK B HR 

This set-point lets you set the clock hour you 
would like to start in 24hr format.  For 
example, if you want to start in the 3 o'clock 
in the afternoon hour, set it to 15.  

Factory 

set to 00.

 

P13 

CLK B MIN 

This set-point lets you set the clock minute 
you would like to start.  For example, if you 
want to start at 8:30 in the morning, you 
would adjust this until it read 30 in the minute 
portion 

Factory set to 00.

 

Summary of Contents for Murphy EMS PRO LITE
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands