138
Reference Manual
00809-0200-4702, Rev CA
Appendix D: Installation Instructions and
Drawings for Safety Shower Monitoring
February 2013
Installation Instructions and Drawings
for Safety Shower Monitoring
1.
Isolate the control valve from the process line pressure, release pressure from both
sides of the valve body, and drain the process media from both sides of the valve. Shut
off all pressure lines to the Shower and Eyewash, releasing all pressure from the Shower
and Eyewash. Use lock-out procedures to be sure that the above measures stay in effect
while you work on the equipment.
2.
Begin Shower Mounting Kit installation by drilling two holes in the Shower Handle as
shown.
3.
Attach the Target Arm to the Shower Handle using two #10-24 X .75 Hex Head Screws,
two #10 Lock Washers, and two #10-24 Hex Nuts.
4.
Loosely attach the Target Magnet to the Target Arm using two #10-24 X .75 Flat Head
Screws, two #10 Lock Washers, and two #10-24 Hex Nuts.
5.
Fasten the two Mounting Brackets to the Shower using the four 1/4-20 X 10.00
Threaded Studs, eight 1/4” Plain Washers, eight 1/4” Lock Washers, and sixteen 1/4-20
Hex Nuts.
6.
Loosely attach the 10 Series GO Switch to the Mounting Plate with the hardware
provided.
7.
Fasten the Mounting Plate to the Mounting Brackets with four
1
/
4
-20 X .75 Hex Head
Screws, four
1
/
4
” Plain Washers, four
1
/
4
” Lock Washers, and four
1
/
4
-20 Hex Nuts. 8.
Adjust the Mounting Plate, 10 Series GO Switch, and Target Magnet as needed so that
the Magnet properly engages the Switch. Tighten hardware to hold the Mounting Plate,
10 Series GO Switch, and Target Magnet in place.
8.
Adjust the Mounting Plate, 10 Series GO Switch, and Target Magnet as needed so that
the Magnet properly engages the Switch. Tighten hardware to hold the Mounting Plate,
10 Series GO Switch, and Target Magnet in place.
9.
Begin Eyewash Mounting installation by loosely attaching the two Mounting Brackets
to the Eyewash using the four 1/4-20 X 10.00 Threaded Studs, eight 1/4” Plain Washers,
eight 1/4” Lock Washers, and sixteen 1/4-20 Hex Nuts.
10.
Loosely attach the Switch Mounting Bracket to the Eyewash Mounting Brackets with
four 1/4-20 X .75 Hex Head Screws, four 1/4” Plain Washers, four 1/4” Lock Washers,
and four 1/4-20 Hex Nuts.
11.
Loosely attach the 10 Series GO Switch to the Switch Mounting Bracket with the
hardware provided.
12.
Attach the Target Magnet to the Target Arm using two #10-24 X .75 Flat Head Screws,
two #10 Lock Washers, and two #10-24 Hex Nuts.
13.
Place the Target Arm on the face of the Eyewash Handle and adjust the position of the
Mounting Brackets, 10 Series GO Switch, and Target Arm so that the Target Magnet
properly engages the Switch. Mark the position of the slot of the Target Arm. Drill two
holes in the Eyewash Handle as shown to be able to attach the Target Arm.
14.
Attach the Target Arm to the Eyewash Handle using two #10-24 X .50 Round Head
Screws, two #10 Lock Washers, and two #10-24 Hex Nuts.
15.
Tighten hardware to hold the Mounting Brackets, 10 Series GO Switch, and Target Arm
in place.
