Efka AB620A5035, Operating Manual

Page: 80 / 104

- AB620A5035 Instruction Manual
- 80 -
11.1 Operator Level
Note
The preset values indicated apply to mode 0 (Parameter 290 = 0).
For preset values applicable to other modes see table in chapter 11.1 »Preset Values Depending on Mode«.
Parameters Designation Unit Max Min Preset Ind.
000 c2
- Number of stitches of start backtack forward
- Number of stitches of start stitch condensing without
stitch regulator
-
Number of stitches of end counting chain suction
Stitches 254 0 2
001 c1
- Number of stitches of start backtack backward
- Number of stitches of start stitch condensing with stitch
regulator
- Number of stitches of start counting chain suction
Stitches 254 0 4
002 c3
- Number of stitches of end backtack backward
- Number of stitches of end stitch condensing with stitch
regulator
- Number of stitches of tape cutter at the start of the
seam
Stitches 254 0 2
003 c4
-
Number of stitches of end backtack forward
- Number of stitches of end stitch condensing without
stitch regulator
-
Number of stitches of tape cutter at the seam end
Stitches 254 0 2
004 LS Light barrier compensating stitches Stitches 254 0 7
005 LSF Number of stitches of the light barrier filter for knitted
fabrics
Stitches 254 0 1
006 LSn Number of light barrier seams 15 1 1
007 Stc Number of stitches for the seam with stitch counting Stitches 999 0 20
008 -F A parameter from the technician level is assigned to key 9 on the
V820 control panel
1 = Softstart On/Off
2 = Ornamental backtack On/Off
3 = Start of sewing blocked with light barrier uncovered On/Off
4 = Unlocking the chain On/Off
8 = Backtack repetition On/Off
9 = Multi-backtack / standard backtack
9 1 1
009 LS Light barrier On/Off 1 0 0
010 SrM Strobel backtack in mode F-290 =56
0 = End backtack off
1 = Single end backtack on2 = Double end backtack on
3 = Double start and double end backtack on
4 = Simple start backtack and simple end tack on
4 0 0 F
013 FA Thread trimmer On/Off 1 0 0
014 Fw Thread wiper On/Off 1 0 0
015 StS Stitch counting On/Off 1 0 0
017 SAb Stop for tape cutting at the seam end On/Off
(Function only when overlock mode is active).
1 0 0
018 UoS 0 =
Sequence “overlock mode with stop”
1 =
Sequence “overlock mode without automatic stop. When the
command “run” is given, the drive runs at the pre-selected
speed. With
pedal in pos. 0 or light barrier covered , the
program switches to the next start of a seam without issuing
signals M1/M2.
2 =
As with setting “1”. But with
pedal in pos. 0 signals M1/M2 will
be issued, and the program switches to the next start of a
seam.
3 = As with setti
ng “1”. But with
pedal -2 signals M1/M2 will be
issued, and the program switches to the next start of a seam.
Intermediate stop and sewing foot lifting with pedal in
pedal -1
is possible.
4 = If the light barrier is covered during the end count for chain
suction, the program switches immediately to the next start of a
seam. If the end count has been completed and the light barrier
remains uncovered, the drive stops.
5 = Tape cutting at the start of the seam with stop
5 0 0