Eaton LoadStar-S JSB Mounting And Operating Instruction Download Page 73

Page: 73 / 104

Mounting- and Operating Instruction Eaton LoadStar-S JSB

40071860396 March 2021 www.ceag.de

34 3-PM-IO-INV Module

Bus connection 3-PM-IO and 3-PM-IO-INV

An RS485 bus is wired for data communication with exter-

nal bus modules.
The wires of the RS 485 bus line must be connected to the

ACU terminal strip at the terminal points RS485 A, RS485

B, +24V OUT and -24V OUT.

NOTE!

A parallel connection of data lines is not permitted and

does not extend the permissible line length.
Wires within a shield can be connected in parallel to supply

voltage to the modules.
The two lower DIL switches on the ACU module for the RS

485 bus must be set to „ON“ at the beginning of the bus

line to activate the 120 Ohm termination resistor.

ATTENTION!

Bus topology: linear, double terminated (no stub lines per-

mitted). Cable type (minimum requirement): IY(ST)Y 4 x 2

x 0.8 mm (twisted pair, shielded) - the cable shield must be

connected to the SE terminals of each module and must

only be earthed in the LoadStar-S control cabinet. The cable

cross-section required for the 24 V bus voltage depends on

the cable length and the number of bus modules (Umin =

19 V DC). Only one pair of wires may be used as data cable

within the shield - it is not permitted to bundle several data

cables within one shielded cable! The 120 Ohm terminating

resistor is integrated in the modules and can be activated

by a bridge at terminals B1/B2.

+24V

-1

+24V

-2

+24V

-3

-24V

-1

-24V

-2

-24V

-3

SE-IN

A-IN

B-IN

SE-

A-

B-

PE1

PE2

Adresse

3-PM-IO

H L Sh1 +24.1 -24.1 A B

Sh2 +24.2 -24.2 IN1.1 IN1.2 IN2.1 IN2.2 IN3.1 IN3.2 IN4.1 IN4.2 IN5.1 IN5.2 IN6.1 IN6.2 K1.COM K1.NO K1.NC

K2.COM K2.NO K2.NC K3.COM K3.NO K3.NC K4.COM

K4.NO K4.NC

HMI ETN +24.3 -24.3 IN7.1 IN7.2 IN8.1 IN8.2 K5.COM K5.NO K6.COM K6.NO

ACU

H L A B

I/O Module

Vertraulich. Nur zum internen Gebrauch.

Summary of Contents for LoadStar-S JSB









































































































Search results

Summary of Contents for LoadStar-S JSB

Reviews:

Related manuals for LoadStar-S JSB

Brands by name

Popular brands

Eaton LoadStar-S JSB, Mounting And Operating Instruction

Search results

Summary of Contents for LoadStar-S JSB

Reviews:

Related manuals for LoadStar-S JSB

Brands by name

Popular brands