background image

14

Mounting- and Operating Instruction  Eaton LoadStar-S JSB

   40071860396   March 2021   www.ceag.de

6 Assembly and installation of the LoadStar-S  

 DANGER!

If the batteries or battery-powered parts of the system are 

handled improperly, there is a risk of injury or death due 

to high currents or electric arcs, which can occur briefly at 

battery discharge.
It is essential that you observe the instructions in this manual 

for disconnecting or connecting the batteries (see „Connec-

ting the battery power supply“).
Ensure that the polarity of the battery banks (battery cabinets 

/ racks) is correct.

 ATTENTION! 

Short circuits and incorrect polarity can damage the battery 

bank or the installations of a LoadStar-S system.
At interventions in the electrics (e.g. connection of control or 

signal lines) or electronics (e.g. plugging or pulling modules in 

the switch cabinet), the ESD protection must be observed!
Never switch the mains or battery power supply on or off 

under load. In some cases, the system must have been 

blocked beforehand by the control unit.

Assembly

Requirements for the work surface / installation site:
Installation on level groand with sufficient bearing capacity.
The installation site must be levelled horizontally.
Holes are provided in the floor plate for fastening to the floor 

or screwing to a base.

Installation

Disconnect all connecting cables (mains and battery power 

supply) from the power supply and secure them against 

unintentional reconnection (e.g. removal of all fuses and 

corresponding protection of the distributor of the general 

mains supply and the battery bank with information signs 

and/or locks).

Install the connecting cables (mains and battery power supp-

ly) with sufficient length reserve up to the installation location 

of the LoadStar-S cabinet. Carry out this work properly and 

professionally in accordance with the applicable directives 

and standards.
Secure all cable entries with the M cable glands provided.
If possible, lay the connecting cables in the cable areas of 

the control cabinet.

 NOTE!

In this illustration, outgoing cables for mains and battery 

power supply of substations were attached to the cabinet 

wall on C-rails (item no. 40071347126) with corresponding 

cable clamps. Do not leave any connecting cables tempo-

rarily loose!
Later additions or conversions of the system equipment are 

possible, but the description of such interventions in the 

internal equipment is not part of these instructions, as such 

work is reserved for specially trained Eaton personnel!
The installation of general and emergency lighting is not 

covered by these instructions.
Install, install and connect the lighting equipment in accor-

dance with the relevant electrical engineering directives and 

standards. In addition, observe all directives and regulations 

of the country in which the system is installed and operated.

Summary of Contents for LoadStar-S JSB









































































































Reviews: