Dynisco LCR7000 Series Operating Manual Download Page 16

Page: 16 / 116

LCR7000 & RHEOSIGHTS P/N: 974194 |

Rev: A

ECO: 52468

www.dynisco.com

From lab to production,

providing a window into the process

-16-

•

Is the 120V power outlet properly grounded? (220 V Europe/Asia)

•

Is the guide bushing in place?

•

Are no objects on the swing arm (eg: beaker)?

•

Is the exhaust hood or snorkel operational?

•

Does the operator have safety glasses?

•

Does the operator have high temp gloves?

•

Is he wearing arm protection long sleeves or lab coat?

•

Has the protective oil been wiped out of barrel?

•

Are the safety shields installed?

The rheometer barrel leaves the factory coated with oil to protect it from rust. This oil

must be removed before accurate rheological data can be obtained. Put two cotton patches

half overlapped directly over the top of the barrel of the still cold rheometer. Use

rheometer-cleaning tool #2 (pictured in the Parts List Section of this manual) to run the

patches up and down the full length of the barrel. The die and die holder nut should always

be removed when cleaning the rheometer barrel. Repeat the process with fresh patches

until the patches come out clean.

Turn the rheometer power switch “ON”. If you hear a continuous beeping sound, turn the

rheometer off and be sure you have connected the load cell correctly, as described under

the Getting Started section. If the rheometer's front panel lights up but there is no

movement on the crosshead, shut the rheometer off, pull out the

EMERGENCY STOP

button, then turn the rheometer back on. Be sure the rheometer safety shield is closed

before attempting to move the rheometer crosshead. If the rheometer cross head moves

up then down and stops it is operating properly and you may continue. If the rheometer is

not working correctly proceed to the trouble shooting section.

At 230º C purge the rheometer with Polyethylene (PE) or Polypropylene (PP). A purge is

simply a charge of material run through the rheometer without collecting data. The purge

run helps eliminate any remnants from previous tests. It also coats and fills micro cavities

in the metals, which can be a cause of variability if the first charge of material is treated like

the following charges.

Before Testing Safety Check

Purging the Rheometer

Summary of Contents for LCR7000 Series





















































































































Search results

Summary of Contents for LCR7000 Series

Reviews:

Related manuals for LCR7000 Series

Brands by name

Popular brands

Dynisco LCR7000 Series, Operating Manual

Search results

Summary of Contents for LCR7000 Series

Reviews:

Related manuals for LCR7000 Series

Brands by name

Popular brands