Dynamic Engineering PCIeBiSerialDb37-BA22 User Manual Download Page 35 | Manualshive

Page: 35 / 44

background image

Embedded Solutions

Page 35

BA22_CHAN_FRAME_LENGTH

[0x34] Tx Frame Length(read/write)

Tx Frame Length Register

Data Bit

Description

31-0

Amount of data required to start transmission

Figure 23 PcieBiSerialDb37BA22 TX Frame Length Register

This read/write port accesses the Frame Length register.  Set the number of Lines per
Frame to be transmitted with this register.
(Line  Idle Length) * 7 * Frame Length = the period in clocks for the transmitted
portion of the Frame.   The FRAME REF is also in clocks and should be larger than this
number for standard operation.

CHAN_TX_PreAmblePat

[0x38] Tx PreAmble (read/write)

Tx PreAmble Pattern Register

Data Bit

Description

7-0

Control Pattern to send during PreAmble

Figure 24 PcieBiSerialDb37BA22 TX PreAmble Pattern Register

This read/write port accesses the PreAmble Pattern register.  Set the control data to
send during PreAmble time.  PreAmble will be sent when the Master Sync has been
detected for PreAmbleLen pixels.   If programmed to 0 length the PreAmble is skipped.

CHAN_TX_PreAmbleLen

[0x3C] Tx PreAmble Length(read/write)

Tx PreAmble Length Register

Data Bit

Description

15-0

Number of PreAmble pixels to send

Figure 25 PcieBiSerialDb37BA22 TX PreAmble Length Register

This read/write port accesses the PreAmble Length register. If programmed to 0 length
the PreAmble is skipped. If set to a non-zero length, that number of PreAmble pixels is

«
...
33
34
35
36
37
...
»

Summary of Contents for PCIeBiSerialDb37-BA22













































Reviews:

No comments

Related manuals for PCIeBiSerialDb37-BA22

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Salda Pages: 20

Brand: IFM Pages: 49

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands