Dräger Cicero EM Instructions For Use Manual Download Page 107

Page: 107 / 196

107

Message, cause and remedy

Messages on the system screen

(In alphabetical order according to priority)

Messages

Cause

Remedy

ECG N ? !
ECG LA ? !
ECG LL ? !
ECG RA ? !
ECG V ? !

ECG electrodes disconnected.

Secure electrodes.

FI O2 CAL ? !

The mainstream FiO

sensor has not been

calibrated.

Change lead/sensor.
Calibrate the FiO

sensor

manually.

Fl O2 INOP !

Sensor calibrated incorrectly?
Sensor changed and/or not calibrated?
Sensor exhausted?
Sensor not plugged in?
Sensor lead defective?
Dräger sensor cell not used?

Calibrate sensor.
Calibrate sensor.
Replace and calibrate cell.
Plug in sensor connector.
Replace sensor housing.
Use original sensor cell.

FLOW INOP !

Flow sensor / flow sensor lead defective? Flow
sensor not plugged in? Flow sensor soiled?

Replace lead / sensor and
calibrate sensor.

Plug in sensor connector.

FLOW SENSOR ? !

No gas flow detected by flow sensor although
ventilation evidently proceeding correctly.

Check flow sensor, replace if
necessary.

Check flow sensor lead.

FRESH GAS ? !

The econometer indicates that the fresh gas reserve

in the manual breathing bag is too low.
(This message is programmed by Dräger Service
on request).

Increase the fresh gas flow. If
necessary, repair leakage in the
hose system.

HORN INOP !

Loudspeaker defective. Alarm tone deactivated.

Call DrägerService

NO S-T !

S-T analysis not possible.

Check electrode positions.

N2O INOP !

O gas measurement faulty.

Call DrägerService

NIBP ARTEFACT !

Movement artefacts detected during measurement.

Secure limb if necessary.
Measurement is repeated
automatically.

NIBP DEFEKT !

Interner elektronischer oder pneumatischer Fehler.

Call DrägerService

PB 8800 COM !

The parameter box is disconnected.

PBOX

OFF !

Parameter box alarms inactive.

Summary of Contents for Cicero EM





































































































































































































Search results

Summary of Contents for Cicero EM

Reviews:

Brands by name

Popular brands

Dräger Cicero EM, Instructions For Use Manual

Search results

Summary of Contents for Cicero EM

Reviews:

Brands by name

Popular brands