Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 359 | Manualshive

Page: 359 / 370

background image

Operating Instructions

Disassembly and Disposal

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 359 / 370

12.5

Safety instructions for the disposal of production waste

The disposal of operating liquids and any harmful cleaning agents is strictly
governed by environmental laws and their regulations.



Collect used materials in containers and have them disposed of

properly by the waste disposal company.



Spilled materials should be covered in a binding agent immediately

and, after binding, be disposed of as hazardous waste.



Take the necessary precautions to catch spilled substances (sealed

floor, catch pans, drip sheets).

12.6

Disposal of production waste

The following waste is accumulated during operation:



Ink, cleaning fluid



Worn consumables



Production auxiliary materials



Cleaning agents

Information



For detailed information on disposal, please observe the safe-

ty data sheets of the manufacturer (see appendix of this man-
ual).

Disposal of replacement parts

Obsolete replacement parts or replacement parts damaged during storage
can be disposed of in small quantities in the ordinary household garbage.
Please observe the local, regional and national laws and regulations as well
as the provisions of the local waste disposal company!

All other components should be returned to Markem-Imaje CSAT GmbH for
reconditioning.

«
...
357
358
359
360
361
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

Brand: WaxJet Pages: 131

ExpressCard 2000

Brand: Magtek Pages: 25

WorkCentre 7232

Brand: Xerox Pages: 13

CX PRINT SERVER 550

Brand: Xerox Pages: 166

Brand: Xerox Pages: 4

Brand: Oki Pages: 28

Brand: BCS Pages: 151

PhotoChrome R-38

Brand: LYSON Pages: 8

PR-INT-MX-RAVAS-ABLE

Brand: Ravas Pages: 26

Brand: Lexmark Pages: 807

Blaster ADVANTAGE

Brand: CognitiveTPG Pages: 20

Brand: Olivetti Pages: 204

Brand: IBM Pages: 16

4510B - Phaser B/W Laser Printer

Brand: Xerox Pages: 10

Brand: Lanier Pages: 4

Brand: Kyocera Mita Pages: 14

Brand: Oki Pages: 309

PRICOM PRICOM C- 5100

Brand: Silex technology Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands