Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 187 | Manualshive

Page: 187 / 370

background image

Operating Instructions

Machine Description

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 187 / 370

4.12.3 Tab Consumables > Print heads

This tab is for monitoring the running time / the useful life of the individual
print heads.

The basis for calculations is the number of the so-called "shots," that is,
how often a print head gives off one or multiple drops simultaneously during
printing or during the cleaning processes. The total number of drops given
off is irrelevant in this respect. In other words: A print head that always cre-
ates a thin, continuous line in the direction of travel will wear out just as fast
as a print head that is used over its total lentgth to create larger, solid-
colored areas.

The print head row 1 is located on the side next to the inside wall of the
printer. The print head row 2 is located on the side of the web of substrate
facing the operator.

Fig. 76. Tab Consumables > Print heads

Pos. Item

Meaning

1

Print head
counter row 1

Indicates the location: The print head row 1 is located on
the side next to the inside wall of the printer.

2

Shots

Indicates the current number of shots given off by the
print head, measured in millions.

3

Running time

Indicates the current running time of the print head in
question, measured in hours.

4

Reset

Hitting the reset key returns the number of shots and the
running time of the particular print head to "0". (This op-
tion only available for MI CSAT.)

5

Print head
counters row 2

Same information as above for the print head row 2,
located on the side of the operator.

6

Useful life:
Common

The expected useful life of a print head

1

2

3

4

7

6

5

«
...
185
186
187
188
189
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: IBM Pages: 102

Brand: Fastjet Pages: 52

WorkCentre 7800 series

Brand: Xerox Pages: 14

WORKCENTRE 7775

Brand: Xerox Pages: 15

WORKCENTRE 7775

Brand: Xerox Pages: 24

WORKCENTRE 7755

Brand: Xerox Pages: 252

WORKCENTRE 7755

Brand: Xerox Pages: 15

WORKCENTRE 7755

Brand: Xerox Pages: 40

WorkCentre 5019

Brand: Xerox Pages: 50

versalink C7020

Brand: Xerox Pages: 20

WorkCentre 4265

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 281

Brand: Xerox Pages: 100

Brand: Xerox Pages: 629

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands