Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 309 | Manualshive

Page: 309 / 370

background image

Operating Instructions

Maintenance and Repair

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 309 / 370

>

Tighten the two attachment blocks.

>

Ensure that the guide roller is
straight and does not wobble.

>

Following these instructions, also
replace the other four guide rollers
one by one in succession.

>

Push the cover back onto the guide
frame of the print head unit.

>

Tighten the screws of the cover.

Adjust the scanning bar of the infeed

height control unit:

>

Release the screws #1 at both
ends of the scanning bar.

>

Rotate the scanning bar until mark
#2 points to the correct value.

>

Tighten the screws of the scanning
bar.

>

Load the new printing substrate
into the printer.

>

If necessary, load the new image
and format files.

>

Close the hinged hood of the print-
er.
The printer is ready to run.

Information

Continuing the rotation of the scanning bar of the infeed height control
unit does not always lead automatically to the next higher or next lower
value. Sometimes, values are skipped that are marked at a different
location.

The reason is that the space for inscriptions on the scanning bar is lim-
ited. The limited space can better be used for inscriptions when the
values are distributed over the entire roller.

2

1

«
...
307
308
309
310
311
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

Brand: LabelTac Pages: 2

Brand: Oki Pages: 282

Brand: MakerPi Pages: 21

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: Felix printers Pages: 9

Brand: Felix printers Pages: 15

Brand: Felix printers Pages: 15

Brand: Oki Pages: 6

Brand: Oki Pages: 44

Brand: Oki Pages: 13

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 28

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Documax A6300 Series

Brand: DataSouth Pages: 180

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands