Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 27

Page: 27 / 370

Operating Instructions

Safety

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 27 / 370

Warning

The safety of the machine is ensured only when all safety equipment
has been properly installed and is active.



Do not operate the machine without safety equipment.



Safety equipment must not be removed until the main switch has

been disabled.



After repair work, replace all safety equipment and check for prop-

er functioning.

Warning



Do not perform repair work on machine components until each

component has been turned off at the main switch and has been
protected with a padlock against being switched back on.



Install a warning sign “Attention! Work on the machine in progress
– Do not start the machine!”

Warning

Risk of injury due to improper handling of compressed air.



Never aim the discharge end of pneumatic hoses at people, oth-

erwise serious injury can result.



Never aim the discharge end of pneumatic hoses at loose objects.



Work on pneumatic equipment must be performed by authorized

and qualified personnel only.

Warning

Tripping hazard.



Make sure no loose cables or objects are left on the floor in the ar-

ea of the machine.

Warning

Danger of slipping due to spilled lubricant or leaking liquids.



Clean up a contaminated floor immediately! Dispose of the clean-

ing cloths in the provided collection containers.

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Search results

Summary of Contents for markem imaje CSAT ITS6 210

Reviews:

Related manuals for markem imaje CSAT ITS6 210

Brands by name

Popular brands

Dover markem imaje CSAT ITS6 210, Operating Instructions Manual

Search results

Summary of Contents for markem imaje CSAT ITS6 210

Reviews:

Related manuals for markem imaje CSAT ITS6 210

Brands by name

Popular brands