Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 356

Page: 356 / 370

Disassembly and Disposal

Operating Instructions

Page 356 / 370

Subject to Technical Modifications

ITS6_135_Manual_EN.doc

Caution



Direct contact with leaking operating fluids can cause damage to

skin.



Wear solvent-resistant gloves and protective eyewear when han-

dling the media.



Avoid contact with operating supplies and cleansers!



Wash exposed skin parts thoroughly. If skin irritation persists, see

a doctor.



Change contaminated or saturated clothing immediately.



Observe the safety data sheets of the substances used.

Caution

Avoid environmental damage from exhausted consumables and
cleansers.



Take precautions to collect spilled consumables and cleansers

(sealed floor, collection pan, small collection pans, collecting tar-
paulins).



Pour binding agent on spilled substances, and dispose of the

soaked binding agent as hazardous waste.



Collect consumables in suitable containers, and dispose of them

through a specialized waste disposal company in an environmen-
tally compatible way.



Observe the applicable environmental regulations for the disposal

of consumables and cleansers.



If required, dispose of exhausted consumables and cleansers as

hazardous waste.



Observe the data sheets from the manufacturers (see Appendix to

this manual).

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Search results

Summary of Contents for markem imaje CSAT ITS6 210

Reviews:

Related manuals for markem imaje CSAT ITS6 210

Brands by name

Popular brands

Dover markem imaje CSAT ITS6 210, Operating Instructions Manual

Search results

Summary of Contents for markem imaje CSAT ITS6 210

Reviews:

Related manuals for markem imaje CSAT ITS6 210

Brands by name

Popular brands