Dover markem imaje CSAT ITS6 210 Operating Instructions Manual Download Page 249 | Manualshive

Page: 249 / 370

background image

Operating Instructions

Operation

© Copyright by Markem-Imaje CSAT GmbH

ITS6_135_Manual_EN.doc

Subject to Technical Modifications

Page 249 / 370

dancer roller system to the web tension control with the attached cut-
and-splice device.

>

Starting from the cut-and-splice device, use the winding diagram at-
tached here as a guide to feed the printing substrate up over the guide
rollers to the web guider and to the web retraction system.

>

Using the winding diagram attached to the print head unit as a guide,
feed the printing substrate through the web retraction system to the
print head unit and then back to the web retraction system. From there,
pull the printing substrate to the friction drive.

>

Briefly unlock the friction drive in order to push the print material be-
tween the two rollers through to the right.

>

From this point, the yellow “Infeed forward” button of the operating
panel must be pushed for further material transport. All safety doors
must be closed first for this purpose.

>

Lead the substrate from the friction drive over the dancer roller to the
cut-and-splice device as shown in the winding diagram.

«
...
247
248
249
250
251
...
»

Summary of Contents for markem imaje CSAT ITS6 210



















































































































































































































































































































































































Reviews:

No comments

Related manuals for markem imaje CSAT ITS6 210

imageCLASS Mf6160dw

Brand: Canon Pages: 64

imageCLASS MF6500 Series

Brand: Canon Pages: 132

imageCLASS MF5550

Brand: Canon Pages: 120

imageCLASS MF5630

Brand: Canon Pages: 85

imageCLASS MF5550

Brand: Canon Pages: 136

IMAGECLASS MF7400

Brand: Canon Pages: 40

imageCLASS MF5850dn

Brand: Canon Pages: 34

imageCLASS MF6500 Series

Brand: Canon Pages: 16

imageCLASS MF6540

Brand: Canon Pages: 82

imageCLASS MF5550

Brand: Canon Pages: 99

imageCLASS MF5630

Brand: Canon Pages: 24

imageCLASS MF5770

Brand: Canon Pages: 2

imagePRESS C7000VP Series

Brand: Canon Pages: 48

imageClass MF5650

Brand: Canon Pages: 40

imageCLASS MF5770

Brand: Canon Pages: 8

imageCLASS MF4880dw

Brand: Canon Pages: 36

imageCLASS MF4890dw

Brand: Canon Pages: 116

ImageCLASS MF4690

Brand: Canon Pages: 387

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands