Dover Imaje 9020 Troubleshooting Manual Download Page 38 | Manualshive

Page: 38 / 54

background image

Troubleshooting

SECTION 06 Troubleshooting

38/54

Replacing the industrial interface card

■ Tools:

2.5 mm Allen wrenches; 2.5 mm flat-bladed screwdriver.

CAUTION:

Unplug the printer from its AC outlet.

■ Disassembly:

□ Open the left side door.

□ Disconnect all the wires connected to the industrial interface board terminal blocks
(cell, tachometer, etc.).

CAUTION:

Identify the wires before removing them.

□ Remove the 2 attachment screws and disconnect the industrial interface board from
the CPU board.

Reassembly:

□ Fit the new industrial interface board on the connector on the CPU board and
reassemble the two mounting screws.

□ Reconnect all the wires to the terminal blocks.

«
...
36
37
38
39
40
...
»

Summary of Contents for Imaje 9020























































Reviews:

No comments

Related manuals for Imaje 9020

Pixma G1000 series

Brand: Canon Pages: 2

Pixma G1000 series

Brand: Canon Pages: 80

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 44

Brand: Z Corporation Pages: 76

WorkCentre Pro 90

Brand: Xerox Pages: 36

Brand: Xerox Pages: 128

wematter Atmosphere

Brand: 3D Systems Pages: 11

da Vinci Jr. 1.0

Brand: XYZ Printing Pages: 3

MICROLINE ML310

Brand: Oki Pages: 32

System 2200 2231w-3

Brand: Wang Pages: 52

Brand: Xerox Pages: 4

Brand: BIXOLON Pages: 20

Brand: Olivetti Pages: 8

Brand: SEWOO Pages: 24

1235N - Phaser Color Laser Printer

Brand: Tektronix Pages: 240

Brand: Xiamen Sojet Electronics Pages: 37

Brand: Xerox Pages: 16

Brand: Infotec Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands