Dover Imaje 9020 Troubleshooting Manual Download Page 23

Page: 23 / 54

Troubleshooting

SECTION 06 Troubleshooting

23/54

■ List of special spare parts for Imaje technicians

Sale of the parts in the table below is reserved to Imaje technicians.

All other spare parts appear in the spare parts and accessories catalog.

Part

number

ENM

ENR

Description

Comments

A28591

Recovery assembly with
equipped single jet

Seals and hardware
included

A28592

Recovery assembly
equipped twin jet

Seals and hardware
included

Gutter adjustment tool

A12230

Nozzle plate O-ring
(EPT 4 × 0.6)

A28155

Modulation assembly O-ring
(EPT 2.3 × 0.6)

A10403

ENM 5836

Tip holder O-ring
(EPT 18.72 × 2.62)

A15218

ENM7802

Teflon hose, 2.7 × 4

A13429

Teflon hose 1.9 × 2.7

EN6540

ENM6540

Piezo wire

Kit of 10 wires

A28629

ADP board

A28668

Single jet piezo board

A28309

Twin jet piezo board

A11794

ENM50145

Potentiometer

Kit of 5 potentiometers

Summary of Contents for Imaje 9020























































Search results

Summary of Contents for Imaje 9020

Reviews:

Related manuals for Imaje 9020

Brands by name

Popular brands

Dover Imaje 9020, Troubleshooting Manual

Search results

Summary of Contents for Imaje 9020

Reviews:

Related manuals for Imaje 9020

Brands by name

Popular brands