Dodge 2012 Charger Owner'S Manual Download Page 410 | Manualshive

Page: 410 / 594

background image

Tire Terminology And Definitions

Term

Definition

B-Pillar

The vehicle B-Pillar is the structural member of the body located
behind the front door.

Cold Tire Inflation Pressure

Cold tire inflation pressure is defined as the tire pressure after the
vehicle has not been driven for at least 3 hours, or driven less
than 1 mile (1.6 km) after sitting for a three hour period. Inflation
pressure is measured in units of PSI (pounds per square inch) or
kPa (kilopascals).

Maximum Inflation Pressure

The maximum inflation pressure is the maximum permissible cold
tire inflation pressure for this tire. The maximum inflation pres-
sure is molded into the sidewall.

Recommended Cold Tire Inflation
Pressure

Vehicle manufacturer’s recommended cold tire inflation pressure
as shown on the tire placard.

Tire Placard

A paper label permanently attached to the vehicle describing the
vehicle’s loading capacity, the original equipment tire sizes and
the recommended cold tire inflation pressures.

408

STARTING AND OPERATING

«
...
408
409
410
411
412
...
»

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Charger

Brand: Kargo Master Pages: 5

Brand: UnderCover Pages: 16

Brand: Neuspeed Pages: 2

Brand: FormFit Pages: 4

Brand: Subaru Pages: 21

Brand: GMC Pages: 20

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: Uebler Pages: 56

Brand: STO N SHO Pages: 7

Parktronic system Volkswagen Golf MK7

Brand: Car-Systems Pages: 10

Brand: Cadillac Pages: 335

Brand: Whispbar Pages: 15

Brand: Aries Pages: 3

Brand: Lund Pages: 12

Brand: Crux Pages: 10

Brand: Toyota Pages: 26

Brand: ROLEC Pages: 2

Brand: Hamron Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands