Dodge 2012 Charger Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 594

background image

Transmitter Battery Replacement

The recommended replacement battery is one CR2032
battery.

NOTE:

•

Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

•

Do not touch the battery terminals that are on the back
housing or the printed circuit board.

1. Remove the emergency key by sliding the mechanical
latch on the back of the RKE transmitter sideways with
your thumb and then pull the key out with your other
hand.

2. Insert the tip of the emergency key or a #2 flat blade
screwdriver into the slot and gently pry the two halves of
the RKE transmitter apart. Make sure not to damage the
seal during removal.

3. Remove the battery by turning the back cover over
(battery facing downward) and tapping it lightly on a
solid surface such as a table or similar, then replace the
battery. When replacing the battery, match the + sign on
the battery to the + sign on the inside of the battery clip,
located on the back cover. Avoid touching the new

24

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
24
25
26
27
28
...
»

Summary of Contents for 2012 Charger



















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2012 Charger

Brand: Cadillac Pages: 3

Brand: Cadillac Pages: 12

Brand: Cadillac Pages: 106

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 326

Brand: Cadillac Pages: 28

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 602

ESCALADE ESV 2004

Brand: Cadillac Pages: 20

ESCALADE EXT 2005

Brand: Cadillac Pages: 460

CT6 SUPER CRUISE 2018

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 337

Brand: Vaisala Pages: 24

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Ford Pages: 52

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: Volvo Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands