Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 71 | Manualshive

Page: 71 / 532

background image

Tether Anchorage Points at All Three Seating
Positions (Mega Cab)

1. Place the child restraint on the seat and adjust the
tether strap so that it will reach over the seat back under
the head restraint to the tether anchor directly behind the
seat.

2. Lift the cover, and attach the hook to the square
opening in the sheet metal.

3. Install the child restraint and remove the slack in the
tether strap according to the manufacturer’s instructions.

Children Too Large for Booster Seats

Children who are large enough to wear the shoulder belt
comfortably, and whose legs are long enough to bend
over the front of the seat when their back is against the
seat back should use the lap/shoulder belt in a rear seat.

•

Make sure that the child is upright in the seat.

Mega Cab Tether Strap Mounting

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

71

2

«
...
69
70
71
72
73
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Lancia Pages: 191

Brand: M7 SPEED Pages: 11

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Toyota Pages: 35

Brand: Honda Pages: 208

Brand: Thule Pages: 12

Brand: Oldsmobile Pages: 2

Brand: TATA Motors Pages: 136

Brand: M7 SPEED Pages: 6

Brand: Meta System Pages: 16

SANICON TURBO 300

Brand: Thetford Pages: 25

Brand: E&G Classics Pages: 4

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: Mitsubishi Pages: 362

Brand: Huf Pages: 6

Brand: Kleinn Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands