Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 532

background image

As a guide, if you are shorter than average, you will
prefer a lower position, and if you are taller than average,
you’ll prefer a higher position. When you release the
anchorage, try to move it up or down to make sure that
it is locked in position.

Automatic Locking Restraint (ALR) Mode – If
Equipped

In this mode, the shoulder belt is automatically pre-
locked. The belt will still retract to remove any slack in
the shoulder belt. The automatic locking mode is avail-
able on all passenger seating positions with a combina-
tion lap/shoulder belt.

When To Use The Automatic Locking Mode

Anytime a child safety seat is installed in a passenger
seating position. Children 12 years old and under should
be properly restrained in the rear seat whenever possible.

How To Use The Automatic Locking Mode

1. Buckle the combination lap/shoulder belt.

2. Grasp the shoulder portion and pull downward until
the entire belt is extracted.

3. Allow the belt to retract. As the belt retracts, you will
hear a clicking sound. This indicates the safety belt is
now in the automatic locking mode.

How To Disengage The Automatic Locking Mode

Disconnect the combination lap/shoulder belt and allow
it to retract completely to disengage the automatic lock-
ing mode and activate the vehicle sensitive (emergency)
locking mode.

44

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
42
43
44
45
46
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Pacbrake Pages: 9

Brand: Hama Pages: 2

Brand: kaarta Pages: 29

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

2012 Escalade Hybrid

Brand: Cadillac Pages: 90

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: Volvo Pages: 19

Brand: Trailboss Pages: 5

Brand: Kia Pages: 10

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: AA Products Pages: 6

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: Demco Pages: 4

Brand: Yakima Pages: 12

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands