Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 428 | Manualshive

Page: 428 / 532

background image

If the solution is dirty or contains a considerable amount
of sediment, clean and flush with a reliable cooling
system cleaner. Follow with a thorough rinsing to remove
all deposits and chemicals. Properly dispose of old
antifreeze solution.

Selection Of Coolant

Use only the manufacturers recommended coolant, refer
to Fluids, Lubricants and Genuine Parts for correct
coolant type.

CAUTION!

Mixing of coolants other than specified HOAT en-
gine coolants, may result in engine damage and may
decrease corrosion protection. If a non-HOAT cool-
ant is introduced into the cooling system in an
emergency, it should be replaced with the specified
coolant as soon as possible.

Do not use plain water alone or alcohol base engine
coolant (antifreeze) products. Do not use additional
rust inhibitors or antirust products, as they may not
be compatible with the radiator engine coolant and
may plug the radiator.

This vehicle has not been designed for use with
Propylene Glycol based coolants. Use of Propylene
Glycol based coolants is not recommended.

428

MAINTAINING YOUR VEHICLE

«
...
426
427
428
429
430
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Camcar Pages: 2

Brand: Toyota Pages: 56

Brand: Vauxhall Pages: 323

Brand: muth Pages: 10

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: Ford Pages: 458

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: Lincoln Pages: 586

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

nERGY ETSA200R-PA

Brand: Soundoff Signal Pages: 3

Brand: Truma Pages: 10

Brand: BabySafe Pages: 43

Brand: E-Lead Pages: 11

Brand: Menabo Pages: 12

Brand: Whispbar Pages: 34

2013 Odyssey Touring

Brand: Honda Pages: 21

ELSEEV hekia S Mode3

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands