Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 342 | Manualshive

Page: 342 / 532

background image

Gross Trailer Weight (GTW)

The gross trailer weight (GTW) is the weight of the trailer
plus the weight of all cargo, consumables and equipment
(permanent or temporary) loaded in or on the trailer in its

⬙

loaded and ready for operation

⬙

condition. The recom-

mended way to measure GTW is to put your fully loaded
trailer on a vehicle scale. The entire weight of the trailer
must be supported by the scale.

Gross Combination Weight Rating (GCWR)

The gross combination weight rating (GCWR) is the total
permissible weight of your vehicle and trailer when
weighed in combination. (Note that GCWR ratings in-
clude a 68 kg (150 lbs) allowance for the presence of a
driver).

Gross Axle Weight Rating (GAWR)

The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
evenly. Make sure that you do not exceed either front or
rear GAWR.

WARNING!

It is important that you do not exceed the maximum
front or rear GAWR. A dangerous driving condition
can result if either rating is exceeded. You could lose
control of the vehicle and have an accident.

Tongue Weight (TW)

The downward force exerted on the hitch ball by the
trailer. In most cases it should not be less than 10% or
more than 15% of the trailer load. You must consider this
as part of the load on your vehicle.

342

STARTING AND OPERATING

«
...
340
341
342
343
344
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: ZAPTEC Pages: 240

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

Brand: Front Runner Pages: 5

Brand: iDataLink Pages: 99

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: WABCO Pages: 48

Brand: GMC Pages: 20

Brand: Whispbar Pages: 85

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Brand: Bestop Pages: 31

Brand: Draw tite Pages: 4

Brand: EFILive Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands