Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 349 | Manualshive

Page: 349 / 532

background image

•

Safety chains must always be used between your
vehicle and trailer. Always connect the chains to the
frame or hook retainers of the vehicle hitch. Cross the
chains under the trailer tongue and allow enough
slack for turning corners.

•

Vehicles with trailers should not be parked on a grade.
When parking, apply the parking brake on the tow
vehicle. Put the tow vehicle automatic transmission in
P for Park. With a manual transmission, shift the
transmission into reverse. And with four-wheel-drive
vehicles, make sure the transfer case is not in neutral.
Always, block or

⬙

chock

⬙

the trailer wheels.

•

GCWR must not be exceeded.

•

Total weight must be distributed between the tow
vehicle and the trailer such that the following four
ratings are not exceeded:

1. GVWR

2. GTW

3. GAWR

4. Tongue weight rating for the trailer hitch utilized
(This requirement may limit the ability to always
achieve the 10% to 15% range of tongue weight as a
percentage of total trailer weight).

Towing Requirements — Tires

− Do not attempt to tow a trailer while using a compact

spare tire.

− Proper tire inflation pressures are essential to the safe

and satisfactory operation of your vehicle. Refer to the
Tires–General Information section of this manual on
Tire Pressures for proper tire inflation procedures.

− Also, check the trailer tires for proper tire inflation

pressures before trailer usage.

STARTING AND OPERATING

349

5

«
...
347
348
349
350
351
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Saab Pages: 75

Brand: Front Runner Pages: 5

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: Metra Electronics Pages: 2

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Vantage 12 Series

Brand: Ecco Pages: 5

Brand: Thule Pages: 2

StreetLine Series

Brand: SAAS Pages: 4

Brand: Quadratec Pages: 12

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Mercedes-Benz Pages: 39

Brand: Club Car Pages: 286

Brand: Hama Pages: 13

Brand: Volvo Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands