Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 252 | Manualshive

Page: 252 / 532

background image

Manual Transmission – If Equipped

Apply the parking brake, place the gearshift control lever
in NEUTRAL and depress the clutch pedal to the floor
before starting the vehicle. This vehicle is equipped with
a clutch interlocking ignition system. It will not start
unless the clutch is fully depressed.

Automatic Transmission – If Equipped

Start the engine with the selector lever in NEUTRAL or
PARK position. Apply the brake before shifting to any
driving range.

The Cummins Diesel engine is equipped with several
features designed to assist cold weather starting and
operation:

•

The engine block heater is a resistance heater installed
in the water jacket of the engine just above and behind
the oil filter. It requires a 110–115 volt AC electrical
outlet with a grounded, three-wire extension cord.

NOTE:

The engine block heater cord is a factory in-

stalled option. If your vehicle is not equipped, heater
cords are available from your authorized Mopar

威

dealer.

•

A 12–volt heater built into the fuel filter housing aids
in preventing fuel gelling. It is controlled by a built-in
thermostat.

•

A heated intake air system both improves engine
starting and reduces the amount of white smoke
generated by a warming engine.

Normal Starting Procedure — Engine Manifold
AirTemperature Above 66°F (19°C)

Observe the Instrument Panel Cluster lights when start-
ing the engine.

1. Always apply the parking brake.

2. Shift into PARK for an automatic transmission. Fully
depress and hold the clutch and shift into NEUTRAL for

252

STARTING AND OPERATING

«
...
250
251
252
253
254
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: BESAFE Pages: 4

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Brand: iOttie Pages: 58

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Roadmaster Pages: 4

Brand: Yakima Pages: 28

Brand: Saab Pages: 288

Brand: Phonocar Pages: 28

Brand: Blue Ox Pages: 5

Brand: Metra Electronics Pages: 17

1997 Park Avenue

Brand: Buick Pages: 420

Brand: Toyota Pages: 244

Brand: Chrysler Pages: 374

Brand: Discount Car Stereo Pages: 4

Brand: BOSSCO Pages: 7

Brand: Briggs & Stratton Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands