Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 193 | Manualshive

Page: 193 / 532

background image

2. Adjust the hours by turning the right side Tune /
Audio control.

3. After the hours are adjusted, press the right side Tune
/ Audio control to set the minutes. The minutes will
begin to blink.

4. Adjust the minutes using the right side Tune / Audio
control.

5. To exit, press any button/knob or wait 5 seconds.

RW/FF (Radio Mode)

Pressing the rewind/fast forward button causes the tuner
to search for the next frequency in the direction of the
arrows. This feature operates in either AM, FM or Satel-
lite (if equipped) frequencies.

TUNE Control (Radio Mode)

Turn the right side rotary control clockwise to increase or
counter-clockwise to decrease the frequency.

AM/FM Button (Radio Mode)

Press the button to select AM or FM Modes.

Setting the Tone, Balance, and Fade

Press the rotary TUNE control and BASS will display.
Turn the TUNE control to the right or left to increase or
decrease the Bass tones.

Press the rotary TUNE control a second time and MID
will display. Turn the TUNE control to the right or left to
increase or decrease the Mid Range tones.

Press the rotary TUNE control a third time and TREBLE
will display. Turn the TUNE control to the right or left to
increase or decrease the Treble tones.

Press the rotary TUNE control a fourth time and BAL-
ANCE will display. Turn the TUNE control to the right or
left to adjust the sound level from the right or left side
speakers.

UNDERSTANDING YOUR INSTRUMENT PANEL

193

4

«
...
191
192
193
194
195
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: LAMBORGHINI Pages: 48

Brand: Ford Pages: 52

Brand: Thule Pages: 8

StreetLine Series

Brand: SAAS Pages: 4

Brand: Volvo Pages: 266

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: POOL-LINE Pages: 2

Brand: Federal Signal Corporation Pages: 20

Brand: Mazda Pages: 196

Brand: Skoda Pages: 288

Brand: Wabtec Pages: 216

MagicWatch MWE850

Brand: Waeco Pages: 200

10-8002-C12167A

Brand: Saleen Pages: 6

Brand: Hellwig Pages: 5

Brand: NavLinkz Pages: 26

Brand: Navman Pages: 10

BUSHMAN 15L ROADIE fridge Base console

Brand: Cruiser Consoles Pages: 6

Brand: Opel Pages: 233

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands