Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 319 | Manualshive

Page: 319 / 532

background image

Limited Use Spare — If Equipped

The limited use spare tire is for temporary emergency use
on your vehicle. This tire is identified by a limited use
spare tire warning label located on the limited use spare
tire and wheel assembly. This tire may look like the
original equipped tire on the front or rear axle of your
vehicle, but it is not. Installation of this limited use spare
tire affects vehicle handling. Since it is not the same tire,
replace (or repair) the original tire and reinstall on the
vehicle at the first opportunity.

WARNING!

The limited use spare tires are for emergency use
only. Installation of this limited use spare tire affects
vehicle handling. With this tire, do not drive more
than 60 mph (100 km/h). Keep inflated to the cold
tire inflation pressure listed on either your tire
placard or limited use spare tire and wheel assembly.
Replace (or repair) the original tire at the first
opportunity and reinstall it on your vehicle. Failure
to do so could result in loss of vehicle control.

Tire Spinning

When stuck in mud, sand, snow, or ice conditions, do not
spin your vehicle’s wheels above 30 mph (48 km/h).

Refer to the paragraph on “Freeing A Stuck Vehicle” in
Section 6 of this manual.

STARTING AND OPERATING

319

5

«
...
317
318
319
320
321
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: kaarta Pages: 29

Brand: Westin Pages: 3

Brand: TrailFX Pages: 6

Brand: AutoWatch Pages: 4

Brand: Nav TV Pages: 3

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: Renault Pages: 340

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: TAUBENREUTHER Pages: 18

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Lexus Pages: 830

Brand: ROADGEAR Pages: 2

Brand: Renault Pages: 3699

Brand: Axxess Pages: 8

Brand: Reliant Pages: 116

Sprinter Shuttle

Brand: L.A. West Pages: 30

Brand: Nav TV Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands