Dodge 2007 Ram Chassis Cab Owner'S Manual Download Page 115 | Manualshive

Page: 115 / 532

background image

WARNING!

You can be seriously, even fatally, injured riding in a
seat with the seatback reclined. Do not ride with the
seatback reclined so that the shoulder belt is no
longer resting against your chest. If you ride in this
position, the shoulder harness will no longer be
restraining you. In a collision you could slide under
the seat belt and receive serious or fatal injuries.
Recline in a seat only when the vehicle is parked.

Adjustable Head Restraints

Head restraints can reduce the risk of neck injury in the
event of impact from the rear. Pull up or push down on
the restraints so that the upper edge is as high as
practical, at least to the level of the ears.

To lower the head restraint, push in the button and then
push down on the head restraint.

Head Restraints

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

115

3

«
...
113
114
115
116
117
...
»

Summary of Contents for 2007 Ram Chassis Cab





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2007 Ram Chassis Cab

Brand: Yakima Pages: 8

Brand: Calix Pages: 5

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: Victory 4x4 Pages: 13

Brand: kincrome Pages: 6

Brand: Rati Pages: 2

Brand: Cadillac Pages: 407

Brand: PUTCO Pages: 2

Brand: POOL-LINE Pages: 2

Brand: AutoLoc Pages: 6

Brand: Prorack Pages: 14

Brand: Subaru Pages: 2

Brand: Subaru Pages: 399

Brand: Mazda Pages: 7

Brand: Ultraplast Pages: 5

Brand: Mercedes-Benz Pages: 66

Brand: Ford Pages: 312

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands